Porter-Cable 4210 & 4212 instruction manual Table of Contents

Page 2

TABLE OF CONTENTS

SAFETY GUIDELINES	3
IMPORTANT SAFETY INSTRUCTIONS	3
ADDITIONAL SPECIFIC SAFETY RULES	4
BACKGROUND INFORMATION	4
OPERATION	5
MISCELLANEOUS TECHNIQUES	5
THROUGH-DOVETAILS WITH CLAMPING BOARDS	6
THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH	8
ALTERNATIVE METHOD - THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH	10
HALF-BLIND DOVETAILS WITH CLAMPING BOARDS	11
USING A ROUTER TABLE	13
ALTERNATE ROUTER BITS	14
HALF-BLIND DOVETAIL TAILBOARDS THICKER THAN 7/8"	17
MITERED THROUGH-DOVETAILS	18
THROUGH-DOVETAIL, SKIPPED PIN METHOD	19
HALF-BLIND DOVETAIL, SKIPPED PIN METHOD	20
SAW KERF ALLOWANCE METHOD	22
MULTIPLE SPACER METHOD	24
END-TO-END JOINTS	24
DRAWERS WITH DOVETAIL DADOS	25
WOODEN HINGES	26
ANGLED JOINTS	29
ACUTE ANGLED JOINTS	32
SLANTED SIDE JOINTS	33
COMPOUND ANGLED JOINTS	34
INLAYED THROUGH-DOVETAILS	37
INLAYED HALF-BLIND DOVETAIL JOINTS	38
INLAYED BOX JOINTS	40
TABLES OF COMMONLY AVAILABLE ROUTER BIT SIZES	41
TROUBLESHOOTING	42
MAINTENANCE	42
SERVICE	42
ACCESSORIES	42
WARRANTY	43
SERVICE CENTER LOCATIONS	Back Cover

2

Image 2

Contents Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety InstructionsBackground Information Additional Safety RulesReplacement Parts Operation Miscellaneous TechniquesTHROUGH-DOVETAILS with Clamping Boards SetupTemplates Mounted to Clamping Boards Cutting the Pins Cutting the TailsTHROUGH-DOVETAILS with Unlimited Board Width Fitting the JointSet the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8Cutting the Joint Using a Router Table THROUGH-DOVETAIL BIT Combinations Readily Available Alternate Router BitsTHROUGH-DOVETAIL Bits HALF-BLIND Dovetail BIT Readily Available Dovetail Dado Bits BOX Joint BitsBOX Joint Bits Readily Available HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAILTHROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the TailsHALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins Page Cutting the Tails Fitting and Cutting the Joint Multiple Spacer MethodEND-TO-END Joints BOX END-TO-END JointsDrawers with Dovetail Dados Dovetail END-TO-END JointsWooden Hinges Hinges with a Drilled HoleHinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Obtuse Angled Joints Setup with the Template Mounted to the Base of the JIGAngled Joints Setup with the Template Mounted to a Clamping Board Cutting the TailsCutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Make the First Joint Inlayed JointsInlayed Through Dovetail Make the Second Joint Inlayed HALF-BLIND DovetailCUT OFF the Inlay Board 100 13/128 050 042 028 014 Inlayed BOX Joint HALF-BLIND Dovetail Bits Tables of Commonly Available Router BIT SizesThrough Dovetail Router BIT Combinations BOX Joint BIT CombinationsAccessories Troubleshooting MaintenanceService Warranty PORTER-CABLE Limited ONE Year WarrantyCanadian PORTER-CABLE Delta Service Centers Michigan