Porter-Cable 4210 & 4212 instruction manual

Page 22

NOTE: For this method, you will need a spacer block equal to the thickness of the saw kerf, typically 1/8" on a standard saw blade. Also, make the boards wider than the final size of the box by the same thickness.

NOTE: This method is very similar to making standard through-dovetails.

22

Fig. 37B

Fig. 37A

FITTING THE JOINT

Fit the joint the same as you would the half-blind dovetail.

SAW KERF ALLOWANCE METHOD

An effective way to match the grain in a decorative box is to make the box from one piece of wood and then cut the lid with a table saw. However, if the dovetails are evenly spaced, they may be unattractive because the saw kerf removed needed material.

Fig. 35D

Fig. 35E

Fig. 35F

D

E

If you remove a bit more material than necessary, remember that it will be hidden in the joint (E) Fig. 35F.

Remove all excess material.

Make the cuts with the router to remove the shaded pins (Fig. 35E).

Adjust the pin board so that the marks align with the straight edge of the templet (D) Fig. 35D.

Install the half-blind template so that its straight edge faces you.

Place the pin board back in the jig.

Step 4 - Shade the pins that will be removed (Fig. 35C). Step 5 -

Step 6 -

Step 7 -

Step 8 -

Step 9 -

Step 10 -

Image 22

Contents Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety InstructionsReplacement Parts Additional Safety RulesBackground Information Operation Miscellaneous TechniquesTemplates Mounted to Clamping Boards SetupTHROUGH-DOVETAILS with Clamping Boards Cutting the Pins Cutting the TailsTHROUGH-DOVETAILS with Unlimited Board Width Fitting the JointSet the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8Cutting the Joint Using a Router Table THROUGH-DOVETAIL Bits Alternate Router BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits Readily Available BOX Joint BitsDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAIL THROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the TailsHALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins Page Cutting the Tails Fitting and Cutting the Joint Multiple Spacer MethodEND-TO-END Joints BOX END-TO-END JointsDrawers with Dovetail Dados Dovetail END-TO-END JointsWooden Hinges Hinges with a Drilled HoleHinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Angled Joints Setup with the Template Mounted to the Base of the JIGObtuse Angled Joints Setup with the Template Mounted to a Clamping Board Cutting the TailsCutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Through Dovetail Inlayed JointsMake the First Joint CUT OFF the Inlay Board Inlayed HALF-BLIND DovetailMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint HALF-BLIND Dovetail Bits Tables of Commonly Available Router BIT SizesThrough Dovetail Router BIT Combinations BOX Joint BIT CombinationsService Troubleshooting MaintenanceAccessories Warranty PORTER-CABLE Limited ONE Year WarrantyCanadian PORTER-CABLE Delta Service Centers Michigan