Multiquip MP25E1, MP275E3, MP25E3, MP24 operation manual HERE’S HOW to GET Help

Page 38

OPERATION MANUAL

HERE’S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

UNITED STATES

Multiquip Corporate Office

 

MQ Parts Department

 

18910 Wilmington Ave.

Tel. (800) 421-1244

800-427-1244

Fax: 800-672-7877

Carson, CA 90746

Fax (800) 537-3927

310-537-3700

Fax: 310-637-3284

Contact: mq@multiquip.com

 

 

 

Mayco Parts

 

Warranty Department

 

800-306-2926

Fax: 800-672-7877

800-421-1244, Ext. 279

Fax: 310-537-1173

310-537-3700

Fax: 310-637-3284

310-537-3700, Ext. 279

 

Service Department

 

Technical Assistance

 

800-421-1244

Fax: 310-537-4259

800-478-1244

Fax: 310-631-5032

310-537-3700

 

 

 

 

 

 

 

MEXICO

 

UNITED KINGDOM

 

MQ Cipsa

 

Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5

Tel: (52) 222-225-9900

Hanover Mill, Fitzroy Street,

Tel: 0161 339 2223

Momoxpan, Cholula, Puebla 72760 Mexico

Fax: (52) 222-285-0420

Ashton-under-Lyne,

Fax: 0161 339 3226

Contact: pmastretta@cipsa.com.mx

 

Lancashire OL7 0TL

 

 

 

Contact: sales@multiquip.co.uk

 

CANADA

 

 

 

Multiquip

 

 

 

4110 Industriel Boul.

Tel: (450) 625-2244

 

 

Laval, Quebec, Canada H7L 6V3

Fax: (450) 625-8664

 

 

Contact: jmartin@multiquip.com

 

 

 

© COPYRIGHT 2009, MULTIQUIP INC.

Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.

Your Local Dealer is:

Image 38
Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents MP2 Series Masonry SawsPage MP25E3 MP275E3 SpecificationsSaw Model MP25E1 MP25E3 MP275E3Dimensions DimensionsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearHazard Symbols Gasoline Powered Models This saw, other property, orSafety Gasoline Powered Engines SafetyNever use fuel as a cleaning agent Rules for Safe OperationBlade Safety Safety Electric Powered ModelsGeneral Safety Always use only outdoor approved Grounded extension cordsSaw Maintenance Cleaning SawTransportation SafetyGeneral Information MP2 SawControls and Components MP2 Saw Electric ModelsStopper Place stopper in tray when filling with water Electric Motor Components Heavy Duty Electric MotorsOperating the engine without an Gasoline Engine ComponentsHonda GX270QWH2 Gasoline Engine Muffler Used to reduce noise and emissionsAssembly Electric Powered Saws Only PRE-SETUP Electric MotorsPre-Setup Conveyor Cart PlacementSaw Blade Definitions Figure Blade InstallationSaw Blades Sawing continues, catastrophic failure will occurMP2 Saw is now ready for wet cutting Connecting the Power FigurePlace the power ON/OFF switch in the OFF position down Dry Cutting Electric Saws OnlyWet Cutting Setup Gasoline Only PRE-SETUP Gasoline EngineAssembly Gasoline Powered Saws Only Mechanical water pump isEngine Oil Check Dry Cutting Setup Gasoline OnlyBefore Starting Quarts 1.1 litersStart-up Electric Motor Shutdown ProcedureSTARTUP/SHUTDOWN Electric Motors STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripFixed Height Cutting Method OperationOperation Step Pedal Cutting MethodMaintenance SAW To adjust jackshaft-to-bladeshaft belt Adjust BeltTension Gasoline Powered SawsTo adjust engine-to-jackshaft belts only Adjust BeltTension Electric Powered SawsTighten the set screws Cutting Head Alignment BladeHorizontal Cutting Head Alignment CheckingVertical Cutting Head AlignmentMaintenance Gasoline Engine Engine MaintenanceWeekly Engine Air CleanerDaily Engine OilEngine Wiring Diagram Honda GX270 QWH2 Engine Wiring DiagramTroubleshooting Blade Blade TroubleshootingTroubleshooting Gasoline Engine Engine TroubleshootingAdjust governor to correct lever Troubleshooting Electric Motor Page HERE’S HOW to GET Help