Multiquip MP275E3, MP25E3, MP25E1, MP24 operation manual Safety Message Alert Symbols

Page 8

SAFETY MESSAGE ALERT SYMBOLS

FORYOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Owner's Manual has been developed to provide

NOTEcomplete instructions for the safe and efficient operation of the MP2 Saw.

For engine maintenance information, please refer to the engine manufacturers instructions for data relative to its safe operation.

Before using this MASONRY SAW, ensure that the operating individual has read and understands all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER

You WILL be KILLED or SERIOUSLY injured if you DO NOT follow directions.

WARNING

You CAN be KILLED or SERIOUSLY injured if you DO NOT follow directions.

CAUTION

You CAN be injured if you DO NOT follow directions.

HAZARD SYMBOLS

Potential hazards associated with operation of the pump will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols. Some examples are listed below:

WARNING - Guards and Covers In Place

NEVER operate the saw without blade guards and covers in place. Adhere to safety guidelines ANSI American National Standards Institute, OSHA or other applicable local regulations.

WARNING - Rotating Blade

Rotating blade can cut and crush.

Keep hands and feet clear.

WARNING - Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

WARNING - Rotating Parts

NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

PAGE 8 — MQ MP2 SERIES SAW — OPERATION MANUAL — REV. #0 (01/26/09)

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents MP2 Series Masonry SawsPage Specifications Saw ModelMP25E3 MP275E3 MP25E1 MP25E3 MP275E3Dimensions DimensionsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearHazard Symbols Gasoline Powered Models This saw, other property, orSafety Never use fuel as a cleaning agentSafety Gasoline Powered Engines Rules for Safe OperationSafety Electric Powered Models General SafetyBlade Safety Always use only outdoor approved Grounded extension cordsSaw Maintenance Cleaning SawTransportation SafetyGeneral Information MP2 SawControls and Components MP2 Saw Electric ModelsStopper Place stopper in tray when filling with water Electric Motor Components Heavy Duty Electric MotorsGasoline Engine Components Honda GX270QWH2 Gasoline EngineOperating the engine without an Muffler Used to reduce noise and emissionsPRE-SETUP Electric Motors Pre-SetupAssembly Electric Powered Saws Only Conveyor Cart PlacementBlade Installation Saw BladesSaw Blade Definitions Figure Sawing continues, catastrophic failure will occurConnecting the Power Figure Place the power ON/OFF switch in the OFF position downMP2 Saw is now ready for wet cutting Dry Cutting Electric Saws OnlyPRE-SETUP Gasoline Engine Assembly Gasoline Powered Saws OnlyWet Cutting Setup Gasoline Only Mechanical water pump isDry Cutting Setup Gasoline Only Before StartingEngine Oil Check Quarts 1.1 litersStart-up Electric Motor Shutdown ProcedureSTARTUP/SHUTDOWN Electric Motors STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripOperation OperationFixed Height Cutting Method Step Pedal Cutting MethodMaintenance SAW Adjust BeltTension Gasoline Powered Saws To adjust engine-to-jackshaft belts onlyTo adjust jackshaft-to-bladeshaft belt Adjust BeltTension Electric Powered SawsCutting Head Alignment Blade Horizontal Cutting Head AlignmentTighten the set screws CheckingVertical Cutting Head AlignmentMaintenance Gasoline Engine Engine MaintenanceEngine Air Cleaner DailyWeekly Engine OilEngine Wiring Diagram Honda GX270 QWH2 Engine Wiring DiagramTroubleshooting Blade Blade TroubleshootingTroubleshooting Gasoline Engine Engine TroubleshootingAdjust governor to correct lever Troubleshooting Electric Motor Page HERE’S HOW to GET Help
Top Page Image Contents