Multiquip MP24 operation manual Specifications, Saw Model, MP25E1 MP25E3 MP275E3

Page 6

SPECIFICATIONS

Table 1. Saw Speciﬁcations

Saw Model	MP25E1		MP25E3	MP275E3	MP2H
Approximate Weight			415 lbs. (188 kg)
Blade Capacity			20 in. blade maximum
Cutting Depth			8 in. with 20 in. blade
Blade Speed			2,240 RPMs		2200 RPMs
Water Pump		115V/60Hz, Thermally protected			Mechanical/Centrifugal
Water Pump		115V/60Hz, Thermally protected			Water Pump
					Water Pump

Table 2. Electric Motor/Engine Speciﬁcations

	Saw Model	MP2H	MP25E1	MP25E3	MP275E3
	Engine/Motor	Honda GX270QWH2
	Type	4-Stroke OHV Single
	Type	Cylinder
		Cylinder
	Bore x Stroke	3.0 x 2.3 in. (77 xx 58
	Bore x Stroke	mm)
		mm)
	Displacement	16.5 cu. in. (270 cc)
	Max Output	9.0HP (6.7 KW) @	5HP	5HP	7.5HP
	Max Output	3600 RPM	Heavy Duty	Heavy Duty	Heavy Duty
		3600 RPM	Heavy Duty	Heavy Duty	Heavy Duty
	Fuel Tank Cap.	1.59 US Gal. (6.0	Electric	Electric	Electric
		1.59 US Gal. (6.0	230V	230V	230V
		liters)	230V	230V	230V
		liters)	Single Phase	Three Phase	Three Phase
	Fuel	Unleaded Gasoline	Single Phase	Three Phase	Three Phase
	Fuel	Unleaded Gasoline	60 Hz	60 Hz	60 Hz
		1.16 US Qt. (1.1	60 Hz	60 Hz	60 Hz
	Lube Oil Cap.	1.16 US Qt. (1.1	Amps F.L	Amps F.L	Amps F.L
	Lube Oil Cap.	liters)	12.0	12.0	12.0
		liters)	12.0	12.0	12.0
	Speed Control	Centrifugal Fly-
	Method	Weight Type
	Starting Method	Recoil Start
	Dimension	14.0 x 16.9 x 16.1 in.
	Dimension	(355 x 430 x 410 mm)
		(355 x 430 x 410 mm)
	Dry Net Weight	55.1 lbs. (25.0 kg)

PAGE 6 — MQ MP2 SERIES SAW — OPERATION MANUAL — REV. #0 (01/26/09)

Image 6

Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents MP2 Series Masonry SawsPage MP25E3 MP275E3 SpecificationsSaw Model MP25E1 MP25E3 MP275E3Dimensions DimensionsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearHazard Symbols Gasoline Powered Models This saw, other property, orSafety Gasoline Powered Engines SafetyNever use fuel as a cleaning agent Rules for Safe OperationBlade Safety Safety Electric Powered ModelsGeneral Safety Always use only outdoor approved Grounded extension cordsSaw Maintenance Cleaning SawTransportation SafetyGeneral Information MP2 SawControls and Components MP2 Saw Electric ModelsStopper Place stopper in tray when filling with water Electric Motor Components Heavy Duty Electric MotorsOperating the engine without an Gasoline Engine ComponentsHonda GX270QWH2 Gasoline Engine Muffler Used to reduce noise and emissionsAssembly Electric Powered Saws Only PRE-SETUP Electric MotorsPre-Setup Conveyor Cart PlacementSaw Blade Definitions Figure Blade InstallationSaw Blades Sawing continues, catastrophic failure will occurMP2 Saw is now ready for wet cutting Connecting the Power FigurePlace the power ON/OFF switch in the OFF position down Dry Cutting Electric Saws OnlyWet Cutting Setup Gasoline Only PRE-SETUP Gasoline EngineAssembly Gasoline Powered Saws Only Mechanical water pump isEngine Oil Check Dry Cutting Setup Gasoline OnlyBefore Starting Quarts 1.1 litersShutdown Procedure STARTUP/SHUTDOWN Electric MotorsStart-up Electric Motor STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripFixed Height Cutting Method OperationOperation Step Pedal Cutting MethodMaintenance SAW To adjust jackshaft-to-bladeshaft belt Adjust BeltTension Gasoline Powered SawsTo adjust engine-to-jackshaft belts only Adjust BeltTension Electric Powered SawsTighten the set screws Cutting Head Alignment BladeHorizontal Cutting Head Alignment CheckingVertical Cutting Head AlignmentMaintenance Gasoline Engine Engine MaintenanceWeekly Engine Air CleanerDaily Engine OilEngine Wiring Diagram Honda GX270 QWH2 Engine Wiring DiagramTroubleshooting Blade Blade TroubleshootingTroubleshooting Gasoline Engine Engine TroubleshootingAdjust governor to correct lever Troubleshooting Electric Motor Page HERE’S HOW to GET Help