Multiquip MP275E3, MP25E3, MP25E1, MP24 operation manual MP2 Series Masonry Saws, Table of Contents

Page 4

MP2 SERIES
MASONRY SAWS
Proposition 65 Warning	2
Silicosis/Respiratory Warnings	3
Table Of Contents	4
Specifications	6
Dimensions	7
Safety Message Alert Symbols	8-9
Rules For Safe Operation	10-12
General Information	13
Controls And Components	14-15
Electric Motor Components	16
Gasoline Engine Components	17
Pre-Setup (Electric Motors)	18-20
Pre-Setup (Gasoline Engine)	21-22
Startup/Shutdown (Electric Motors)	23
Startup/Shutdown (Gasoline Engine)	24-25
Operation	26
Maintenance (Saw)	27-29
Maintenance (Gasoline Engine)	30-31
Engine Wiring Diagram	32
Troubleshooting - Blade	33
Troubleshooting (Gasoline Engine)	34-35
Troubleshooting (Electric Motor)	36

Specification and part number

NOTEare subject to change without

notice.

PAGE 4 — MQ MP2 SERIES SAW — OPERATION MANUAL — REV. #0 (01/26/09)

Image 4

Contents Models Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents MP2 Series Masonry SawsPage Specifications Saw ModelMP25E3 MP275E3 MP25E1 MP25E3 MP275E3Dimensions DimensionsSafety Message Alert Symbols Rotating blade can cut and crush Keep hands and feet clearHazard Symbols Gasoline Powered Models This saw, other property, orSafety Never use fuel as a cleaning agentSafety Gasoline Powered Engines Rules for Safe OperationSafety Electric Powered Models General SafetyBlade Safety Always use only outdoor approved Grounded extension cordsSaw Maintenance Cleaning SawTransportation SafetyGeneral Information MP2 SawControls and Components MP2 Saw Electric ModelsStopper Place stopper in tray when filling with water Electric Motor Components Heavy Duty Electric MotorsGasoline Engine Components Honda GX270QWH2 Gasoline EngineOperating the engine without an Muffler Used to reduce noise and emissionsPRE-SETUP Electric Motors Pre-SetupAssembly Electric Powered Saws Only Conveyor Cart PlacementBlade Installation Saw BladesSaw Blade Definitions Figure Sawing continues, catastrophic failure will occurConnecting the Power Figure Place the power ON/OFF switch in the OFF position downMP2 Saw is now ready for wet cutting Dry Cutting Electric Saws OnlyPRE-SETUP Gasoline Engine Assembly Gasoline Powered Saws OnlyWet Cutting Setup Gasoline Only Mechanical water pump isDry Cutting Setup Gasoline Only Before StartingEngine Oil Check Quarts 1.1 litersSTARTUP/SHUTDOWN Electric Motors Shutdown ProcedureStart-up Electric Motor STARTUP/SHUTDOWN Gasoline Engine Place the Choke Lever in the Closed positionStopping the Engine Starter GripOperation OperationFixed Height Cutting Method Step Pedal Cutting MethodMaintenance SAW Adjust BeltTension Gasoline Powered Saws To adjust engine-to-jackshaft belts onlyTo adjust jackshaft-to-bladeshaft belt Adjust BeltTension Electric Powered SawsCutting Head Alignment Blade Horizontal Cutting Head AlignmentTighten the set screws CheckingVertical Cutting Head AlignmentMaintenance Gasoline Engine Engine MaintenanceEngine Air Cleaner DailyWeekly Engine OilEngine Wiring Diagram Honda GX270 QWH2 Engine Wiring DiagramTroubleshooting Blade Blade TroubleshootingTroubleshooting Gasoline Engine Engine TroubleshootingAdjust governor to correct lever Troubleshooting Electric Motor Page HERE’S HOW to GET Help

TABLE OF CONTENTS

MP2 SERIES

MASONRY SAWS