Multiquip FS3SP Concrete SAW Inspection -BLADE Placement, Diamond Blade Placement

Page 24

FS3SP CONCRETE SAW — INSPECTION -BLADE PLACEMENT

NOTE

The following steps should be accomplished before placing the diamond blade on the

blade shaft.

■Place the console ON/OFF button in the OFF position.

■Raise the saw to a high position by cranking the Raise/Lower handle in a counterclockwise direction.

■Use the Blade Nut Wrench & Blade Shaft Locking Wrench stored in the lower section of the console to install the diamond blade.

■Reference Figure 13 (Diamond Blade Placement) when removing or installing the diamond blade.

1. Belt Guard – Unscrew the guard security knob and water hose quick disconnect fitting and remove blade guard (1) from its bayonet fitting and set it beside the saw.

2. Shaft Lock Tool – Remove the shaft lock tool (2) from the tool holder and insert the pointed end through the front of the saw frame into the machined hole in the blade shaft. A conveniently placed opening on the front of the saw frame permits the use of the shaft lock tool. This tool inhibits the shaft from rotating when applying torque to the blade nut.

3. Blade Nut Wrench – Remove the blade nut wrench (3) fro the tool holder and unscrew the blade shaft nut (right-side). This nut loosens clockwise and tightens counter- clockwise.

4. Blade Nut – Remove the blade nut (4). For reassembly, DO NOT over tighten the blade nut against the outer flange. Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m.

5. Outside Blade Flange (Collar) – Ensure that the flange face is clean and free of debris and is placed flush against the diamond blade (7). Check that the drive pin goes through the blade pin hole (6) and seats properly into the inner flange (8).

6. Blade Pin Hole – Align this hole with the drive pin hole on the inner flange collar.

7. Diamond Blade – Ensure that the proper blade has been selected for the job. Pay close attention to the directional arrow on the blade, clockwise for right-sidecutting, counter-clockwise for left-sidecutting. The arbor hole of the blade must match the 1" arbor of the blade shaft.

8. Inner Flange Collar – This flange is fixed upon the blade shaft, and is manufactured with a drive pin hole. The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade.

Figure 13. Diamond Blade Placement

PAGE 24 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #0 (07/15/02)

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Concrete SAW Page Heres HOW to GET Help Table of Contents Parts Ordering Procedures UPS Ground Service at no charge for freightFS3SP Concrete SAW Safety Message Alert Symbols Seriously injured if you do not follow directionsAlways wear approved respiratory protection Always wear approved eye and hearing protectionMachine Safety Decals FS3SP Concrete SAW DecalsGeneral Safety Spilled on a hot engineDiamond Blade Safety SAW Transportation SafetyFS3SP Concrete SAW Rules for Safe Operation Maintenance Safety FS3SP Concrete SAW Rules for Safe OperationEmergencies FS3SP Concrete SAW Dimensions Description Dimension MMFS3SP Concrete SAW Weights FS3SP Concrete SAW Major Components FS3SP Concrete Saw Basic ComponentsPart Name Not ShownFS3SP Concrete SAW Console Components Operation hours saw has been in useThrough the saw ChokeTo Change/Clean Air Filter Initial ServicingEngine Oil Dip Stick Engine Oil LimitsEngine Oil Filler and Cap Engine Drain BoltPower Plants FS3SP Concrete SAW General InformationFamiliarization Blade Guard Assembly Under Carriage SystemBlade Drive System Water SystemFS3SP Concrete SAW Inspection Before StartingEngine Oil Check SeasonDo not overfill the battery Additionally, when connecting the positiveFS3SP Concrete SAW Inspection -BLADE Rotation downcuts with the turn of the shaftOperating area Poor performance and/or blade damageFS3SP Concrete SAW Inspection -BLADE Placement Diamond Blade PlacementGuards and Covers Check B7.5Check the following on the blade flange cover Belts and CoversBelts and Pulleys FS3SP Concrete SAW- Initial START-UP Pull the Choke Knob up into the Open positionPush the Start SwitchFigure 23 to start the engine Push the console engine ON/OFF switch to the OFF positionFS3SP Concrete SAW Initial START-UP Stopping the EngineFS3SP Concrete SAW Operation Saw AlignmentWet Saw Operation For wet sawingFactors for sawing economy Finishing a CutDiamond Blades and Blade Speed Blade SpeedFS3SP Concrete SAW Maintenance General Engine CareBearing Lubrication Care AdjustV-Belt Alignment/Replacement Pulleys Complete DriveV-Belts Replacement steps 1 throughGeneral Transmission Care Drive Chainwill Reduce Chain LifeBlade Shaft Bearing Replacement Replacement of the Blade Shaft BearingsRotate the engine down to provide slack in the V-Belts DriveV-Belts Replacement General CleanlinessDriveV-Belt Check Loosen the 4 3/8 HHC screws page 48, itemPage FS3SP SAW Explanation of Code in Remarks Column Items Found In the Remarks ColumnItems Found In the Items Number Column FS3SP Concrete SAW Suggested Spare Parts FS3SP Concrete SAW Troubleshooting Engine Engine TroubleshootingFS3SP Concrete SAW Troubleshooting Engine Sympton Possible Cause SolutionFS3SP Concrete SAW Name Plate and Decals FS3SP Concrete SAW Name Plate and Decals FS3SP Concrete SAW Under Carriage Assy WHEEL, 5D X 2W X .625 ID #400 CAP FS3SP Concrete SAW Rear Axle Assy Rear Axle Assy FS3SP Concrete SAW Blade Shaft Assy Part Name QTY Remarks FS3SP Concrete SAW Engine Mount Assy MOUNT, Engine Assy FS3SP Concrete SAW Pointers and Covers Assy FS3SP Concrete SAW Pointers and Covers Assy FS3SP Concrete SAW Water System Assy 15546 15076FS3SP Concrete SAW Basic Platform Assy Basic Platform AssySCREW, HHC, Washer 1/4- 20 X 3/4 FS3SP Concrete SAW Blade Mist 20 -INCH Assy GUARD, Blade 20 Assy FS3SP Concrete SAW Manual Raise and Lower Assy FS3SP Concrete SAW Manual Raise and Lower Assy FS3SP Concrete SAW Plug KIT Push Assy Part Name QTY. Remarks FS3SP Concrete SAW Plug KIT Self Proppelled Assy FS3SP Concrete SAW Plug KIT Self Proppelled Assy 10024 NUT, Nyloc 1/4-20 15340FS3SP Concrete SAW Battery BOX Assy Battery BOX AssyFS3SP Concrete SAW Battery BOX Assy 1520310024 NUT, Nylock 1/4 0471 FS3SP Concrete SAW Platform Bare Assy 15035 1506915214 15215Transmission Assy FS3SP Concrete SAW Transmission Assy FS3SP Concrete SAW Transmission Assy SCREW, HHC, Washer 10- 32 X 5/8 CABLE, Throttle 314VTT- 2- 30 1/4FS3SP Concrete SAW Engine Assy 15729 1510415743 15386FS3SP Concrete SAW Wiring Diagram Console SideFS3SP Electric Start Wiring Diagram Rocker Switches Terms and Conditions of Sale Parts Page FAX 310
Top Page Image Contents