Multiquip SHS81A manual Diamond Blade Safety, Saw Transportation Safety

Page 10

SHS81A CUT-OFF SAW — RULES FOR SAFE OPERATION

NEVER leave the machine unattended while running.

NEVER run the engine without the air filter. Severe engine damage could occur.

NEVER wear jewelry or loose fitting clothing that may snag on the controls or moving parts, this can cause a serious injury.

NEVER operate this saw without the blade guard, or other protective guards in place.

NEVER stand behind or in front of the blade path while the engine is running.

NEVER use abrasive blades that are less the 1/8" (3.17 mm) thick.

NEVER exceed maximum blade speed shown for each blade size. Excessive speed could result in blade breakage.

NEVER use a damaged saw or blades.

NEVER try to stop a moving blade with your hand.

NEVER use an abrasive blade that has been dropped.

NEVER use carbide-tipped or toothed type blades of any kind.

NEVER use segmented diamond blades unless they are specifically designed for high-speed, hand-held saws.

NEVER place 1 inch (25.4 mm) arbor hole blades on 20 mm flanges.

NEVER use the side of a cutting-off blade as a grinder.

NEVER cock, jam or wedge the blade in the cut.

NEVER operate the saw if the blade does not stop rotating when the throttle trigger is released.

NEVER start cutting until you have a clear work area and secure footing.

NEVER allow other persons to be near the saw when starting, refueling, or when the saw is operating.

NEVER allow bystanders or animals in the work area while using a cutting-off machine.

NEVER touch a dry cutting diamond blade immediately after use. These blades require several minutes to cool after each cut.

NEVER use damaged or worn blade flanges. Discard any damage or worn saw parts.

NEVER allow blade exposure from the guard to be more than 180 degrees.

NEVER operate this saw without both hands on the handles.

Diamond Blade Safety

Use appropriate steel centered diamond blades manufactured for use on concrete saws.

WARNING

ALWAYS inspect diamond blades before each use. The blade should exhibit no cracks,

dings, or flaws in the steel centered core and/or rim. Center (arbor) hole must be undamaged and true.

Examine blade flanges for damage, excessive wear and cleanliness before mounting

blade. Blade should fit snugly on the shaft and against the inside/outside blade flanges.

Ensure the blade is marked with an operating speed greater than the blade shaft speed of the saw.

Only cut the material that is specified by the diamond blade. Read the specifications of the diamond blade to ensure the proper tool has been matched to the material being cut.

ALWAYS keep blade guards in place. Exposure of the diamond blade must not exceed 180 degrees.

Ensure that the diamond blade does not come into contact with the ground or surface during transportation. DO NOT drop the diamond blade on ground or surface.

The engine governor is designed to permit maximum engine speed in a no-load condition. Speeds that exceed this limit may cause the diamond blade to exceed the maximum safe allowable speed.

Ensure that the blade is mounted correctly for proper operation.

Saw Transportation Safety

NEVER transport the saw with the blade mounted.

ALWAYS use caution when lifting and transporting this saw.

ALWAYS tie-down the saw when transporting.

ALWAYS use caution and follow the instructions when loading and unloading the saw.

PAGE 10 — SHS81A CUT-OFF SAW — OPERATION AND PARTS MANUAL — REV. #0 (01/30/08)

Image 10
Contents SideWinder Page Page SHS81A CUT-OFF SAW Table of Contents Parts Department Service DepartmentWarranty Department Technical AssistanceSHS81A CUT-OFF SAW Safety Message Alert Symbols SHS81A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazardSHS81A CUT-OFF SAW Rules for Safe Operation General Safety SHS81A CUT-OFF SAW Rules for Safe OperationDiamond Blade Safety Saw Transportation SafetySHS81A CUT-OFF SAW Rules for Safe Operation EmergenciesSHS81A CUT-OFF SAW Specifications SHS81A CUT-OFF SAW Decal Placement Machine Operation And Safety Decals10 9 8 7 6 SHS81A CUT-OFF SAW Controls & Components SHS81A CUT-OFF SAW Blade Installation Instructions Tool Kit Blade Installation ProcedureSocket Head Cap Screw w/ Washer H SHS81A CUT-OFF SAW Water KIT Installation InstructionsHex Key Tool K Included with Tool Kit SHS81A CUT-OFF SAW Blades Diamond BladeFuel Check SHS81A CUT-OFF SAW Initial START-UP/OPERATIONStarting SHS81A CUT-OFF SAW Initial START-UP/OPERATION Shut-downBelt Changing Procedure Belt Guard Cover RemovalSHS81A CUT-OFF SAW Maintenance Reversing the Cutting Arm Procedure Tool KitRe-attaching Cover Guard SHS81A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresSHS81A CUT-OFF SAW Troubleshooting Blade SHS81A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine DRY Filter Kits SHS81A CUT-OFF SAW Filter KitsPart NO. Column SHS81A CUT-OFF SAW Explanation of Parts Section RemarksNO. Column QTY. ColumnSHS81A CUT-OFF SAW Suggested Spare Parts To 3 UnitsSHS81A CUT-OFF SAW Muffler Assy Part Name SHS81A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS81A CUT-OFF SAW Crankcase Assy Plate SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS81A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS81A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS81A CUT-OFF SAW Flywheel Assy Pawl SET SHS81A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS81A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS81A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS81A CUT-OFF SAW Carburetor Assy Throttle Valve SHS81A CUT-OFF SAW Crankshaft / Piston Assy SHS81A CUT-OFF SAW Crankshaft and Piston Assy RING, Piston PINSHS81A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS81A CUT-OFF SAW Tools SHS81A CUT-OFF SAW Tools Recommended Diamond Blades For your Side Winder Saw Page HERE’S HOW to GET Help