Multiquip SHS81A manual Belt Changing Procedure, Belt Guard Cover Removal

Page 21

SHS81A CUT-OFF SAW — MAINTENANCE

V-Belt Changing Procedure

N

Remove the 2 hex nuts Land hex screw and washer M to gain access to the V-belt on the clutch side. Remove V-belt cover .

Figure 14. Belt Guard Cover Removal

Remove the 2 hex nuts Jand hex screw and guard adjustment knob I to gain access to the V-belt on the spindle side. Remove the Cover Guard K.

Figure 15. Re-Installing Cover Guard

Using the provided wrench, loosen the three nuts M to reduce the tension on the V-belt, then turn the V-beltTensioning Cam L until the V-belt is completely slacked.

Figure 16. V-Belt Tensioning

Remove the V-belt from the clutch and spindle pulleys. Install the new V-belt around both pulleys. It is essential that the drive V-belt is properly positioned around both the clutch and spindle pulleys.

Figure 17. Drive V-Belt

SHS81A CUT-OFF SAW — OPERATION AND PARTS MANUAL — REV. #0 (01/30/08) — PAGE 21

Image 21
Contents SideWinder Page Page SHS81A CUT-OFF SAW Table of Contents Warranty Department Service DepartmentParts Department Technical AssistanceSHS81A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazard SHS81A CUT-OFF SAW Safety Message Alert SymbolsSHS81A CUT-OFF SAW Rules for Safe Operation SHS81A CUT-OFF SAW Rules for Safe Operation General SafetySaw Transportation Safety Diamond Blade SafetyEmergencies SHS81A CUT-OFF SAW Rules for Safe OperationSHS81A CUT-OFF SAW Specifications Machine Operation And Safety Decals SHS81A CUT-OFF SAW Decal Placement10 9 8 7 6 SHS81A CUT-OFF SAW Controls & Components Tool Kit Blade Installation Procedure SHS81A CUT-OFF SAW Blade Installation InstructionsSHS81A CUT-OFF SAW Water KIT Installation Instructions Socket Head Cap Screw w/ Washer HHex Key Tool K Included with Tool Kit Diamond Blade SHS81A CUT-OFF SAW BladesSHS81A CUT-OFF SAW Initial START-UP/OPERATION Fuel CheckStarting Shut-down SHS81A CUT-OFF SAW Initial START-UP/OPERATIONBelt Guard Cover Removal Belt Changing ProcedureSHS81A CUT-OFF SAW Maintenance Tool Kit Reversing the Cutting Arm ProcedureRe-attaching Cover Guard Air/Fuel Filter Maintenance Procedures SHS81A CUT-OFF SAW Maintenance AIR/FUEL FilterSHS81A CUT-OFF SAW Troubleshooting Blade Troubleshooting Engine SHS81A CUT-OFF SAW Troubleshooting EngineTroubleshooting Engine SHS81A CUT-OFF SAW Filter Kits DRY Filter KitsNO. Column SHS81A CUT-OFF SAW Explanation of Parts Section RemarksPart NO. Column QTY. ColumnTo 3 Units SHS81A CUT-OFF SAW Suggested Spare PartsSHS81A CUT-OFF SAW Muffler Assy Part Name SHS81A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS81A CUT-OFF SAW Crankcase Assy Plate SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS81A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS81A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS81A CUT-OFF SAW Flywheel Assy Pawl SET SHS81A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS81A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS81A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS81A CUT-OFF SAW Carburetor Assy Throttle Valve SHS81A CUT-OFF SAW Crankshaft / Piston Assy RING, Piston PIN SHS81A CUT-OFF SAW Crankshaft and Piston AssySHS81A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS81A CUT-OFF SAW Tools SHS81A CUT-OFF SAW Tools Recommended Diamond Blades For your Side Winder Saw Page HERE’S HOW to GET Help