Multiquip manual SHS81A CUT-OFF SAW Maintenance AIR/FUEL Filter

Page 25

SHS81A CUT-OFF SAW — MAINTENANCE (AIR/FUEL FILTER)

Air/Fuel Filter Maintenance Procedures

Figure 25. Fuel Filter

Figure 26. Pre-Filter

Figure 27. Main Filter Element

Figure 28. Supplementary Filter

Check the fuel filter G located inside the fuel tank periodically for dirt/debris build up. It is recommended to change the fuel filter every 50 tanks of fuel.

This engine is a 2-stroke gasoline engine requiring a specific fuel to oil mixture of 50:1(2%). It is recommended to use an unleaded gasoline rated at 92 octane (premium) with an oil for use on 2-stroke engines only. See Figure 13.

It is highly recommended to keep a supply of spare pre-filterson hand.Maintaining the foam pre -filter, and regular exchanges will prolong the life of the main filter element.

Every 8 hours of operation, remove the pre-air cleaner cover

Iand wash the foam pre-cleanerH in warm fresh soapy

water. Let dry thoroughly. When dry, completely coat the filter with only an approved foam filter oil.

Every 8 hours of operation, remove the covers Iand J and inspect the main filter element. Clean the main filter element Kby vigorously shaking out and dusting off with a soft brush. DO NOT air blast clean this element with compressed gas.

The main filter element should be replaced after three pre filter changes

Every 8 hours of operation, inspect the supplementary filter

element L. Clean the supplementary filter element L by

vigorously shaking out and dusting off with a soft brush. DO NOT air blast clean this element with compressed gas.

The supplementary filter element should be replaced after three pre filter changes.

SHS81A CUT-OFF SAW — OPERATION AND PARTS MANUAL — REV. #0 (01/30/08) — PAGE 25

Image 25
Contents SideWinder Page Page SHS81A CUT-OFF SAW Table of Contents Warranty Department Service DepartmentParts Department Technical AssistanceSHS81A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazard SHS81A CUT-OFF SAW Safety Message Alert SymbolsSHS81A CUT-OFF SAW Rules for Safe Operation SHS81A CUT-OFF SAW Rules for Safe Operation General SafetySaw Transportation Safety Diamond Blade SafetyEmergencies SHS81A CUT-OFF SAW Rules for Safe OperationSHS81A CUT-OFF SAW Specifications Machine Operation And Safety Decals SHS81A CUT-OFF SAW Decal Placement10 9 8 7 6 SHS81A CUT-OFF SAW Controls & Components Tool Kit Blade Installation Procedure SHS81A CUT-OFF SAW Blade Installation InstructionsSocket Head Cap Screw w/ Washer H SHS81A CUT-OFF SAW Water KIT Installation InstructionsHex Key Tool K Included with Tool Kit Diamond Blade SHS81A CUT-OFF SAW BladesFuel Check SHS81A CUT-OFF SAW Initial START-UP/OPERATIONStarting Shut-down SHS81A CUT-OFF SAW Initial START-UP/OPERATIONBelt Guard Cover Removal Belt Changing ProcedureSHS81A CUT-OFF SAW Maintenance Tool Kit Reversing the Cutting Arm ProcedureRe-attaching Cover Guard Air/Fuel Filter Maintenance Procedures SHS81A CUT-OFF SAW Maintenance AIR/FUEL FilterSHS81A CUT-OFF SAW Troubleshooting Blade Troubleshooting Engine SHS81A CUT-OFF SAW Troubleshooting EngineTroubleshooting Engine SHS81A CUT-OFF SAW Filter Kits DRY Filter KitsNO. Column SHS81A CUT-OFF SAW Explanation of Parts Section RemarksPart NO. Column QTY. ColumnTo 3 Units SHS81A CUT-OFF SAW Suggested Spare PartsSHS81A CUT-OFF SAW Muffler Assy Part Name SHS81A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS81A CUT-OFF SAW Crankcase Assy Plate SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS81A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW Lifting Handle and Roller Assy SHS81A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS81A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS81A CUT-OFF SAW Flywheel Assy Pawl SET SHS81A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS81A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS81A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS81A CUT-OFF SAW Carburetor Assy Throttle Valve SHS81A CUT-OFF SAW Crankshaft / Piston Assy RING, Piston PIN SHS81A CUT-OFF SAW Crankshaft and Piston AssySHS81A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS81A CUT-OFF SAW Tools SHS81A CUT-OFF SAW Tools Recommended Diamond Blades For your Side Winder Saw Page HERE’S HOW to GET Help