Grizzly G3619 instruction manual Length AMP Rating

Page 5

Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

AMP RATING

25ft

 

50ft

 

100ft

0-6

18

 

16

 

16

7-10

18

 

16

 

14

11-12

16

 

16

 

14

13-16

14

 

12

 

12

17-20

12

 

12

 

10

21-30

10

 

10

 

No

 

 

 

 

 

 

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It is safer than using your hand and frees both hands to operate tool.

13.DO NOT OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. On machines with mag- netic contact starting switches there is a risk of starting if the machine is bumped or jarred. Always disconnect from power source before adjusting or servicing. Make sure switch is in OFF position before recon- necting.

17.MANY WOODWORKING TOOLS CAN “KICKBACK” THE WORKPIECE toward the operator if not handled properly. Know what conditions can create “kickback” and know how to avoid them. Read the manual accompanying the machine thoroughly.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER OPERATE A MACHINE WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Full mental alert- ness is required at all times when running a machine.

21.NEVER ALLOW UNSUPERVISED OR UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to the operation of the machine are approved, correct, safe, and clearly understood.

24" & 27" Resaw Bandsaws

-3-

Image 5
Contents Models G3619/G3620/G9963/G9966 Resaw BandsawsPage Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For Bandsaws Model G3619 Model G9963 Circuit RequirementsModel G3620/G9966 440V Operation Typical plug configuration for Three-phase operationGrounding Extension Cords Commentary General InformationUnpacking Piece Inventory Site Considerations Clean UpBeginning AssemblyTo mount the fence To install the dust portFence Dust Port Identification AdjustmentsBlade Guides Guide PostG9963/G9966 Blade Guides G3619/G3620 Blade GuidesG9963/G9966 Tracking G3619/G3620 TrackingTo center track your blade To track the bladeTo center the support bearings laterally To adjust the support bearings behind the bladeSupport Bearings Guide Blocks Make sure the bandsaw is unplugged Blade Guard Table StopTo center the blade guard Table Tilt To tilt the table Disconnect power to the bandsawBlade Tension To adjust the tensionTest Run To adjust the fence so it is parallel with the blade Fence Adjustment Blade LeadBlade Selections OperationsBlade Length Blade WidthBlade Breakage Tooth PitchBlade Care Blade Changes To complete a stacked cut Ripping Stacked CutsTo perform ripping operations Resawing To resaw lumber, follow the procedure belowBelts MaintenanceMiscellaneous LubricationPage Page 24 & 27 Resaw Bandsaws 24 & 27 Resaw Bandsaws Closure Machine Data Sheet G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 Frame Fence Rail Grizzly Model G9963/G9966 27 Bandsaw G9963/G9966 Arin g C o G9963/G9966 189 24 & 27 Resaw Bandsaws 8026 Hinge PIN Support Bearing Troubleshooting Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC