Grizzly instruction manual Circuit Requirements, Model G3619 Model G9963

Page 7

SECTION 2: CIRCUIT REQUIREMENTS

Model G3619

 

Model G9963

 

 

 

 

 

 

The Model G3619 Bandsaw is pre-wired for sin- gle-phase, 220V operation. Under normal use, the Model G3619 5 HP motor draws approximately 22 amps. We recommend a 30 amp circuit. This includes a 30 amp circuit breaker and wiring rated for at least 30 amps. This should be satisfactory for normal use, while providing enough protection against damage caused by an overloaded circuit. If frequent circuit failures occur when using the bandsaw, contact our service department or your local electrical contractor.

This bandsaw must be connected to its own dedicated circuit; it should not share a circuit with any other machine. A standard 2-pole breaker is necessary for use with the Model G3619.

This bandsaw is not supplied with a power plug. We recommend using a NEMA-style L6-30 plug and outlet similar to Figure 1. You may also “hard- wire” the bandsaw directly to your panel, provided you place a disconnect near the machine.

Figure 1. Typical 220V 3-prong plug and outlet.

The Model G9963 Bandsaw is pre-wired for single-phase, 220V operation. Under normal use, the Model G9963 7.5 HP motor draws approxi- mately 33 amps. We recommend using a 50 amp circuit. This includes a 50 amp circuit breaker and wiring rated for at least 50 amps. If frequent circuit failures occur when using the bandsaw, contact our service department or your local elec- trical contractor.

This bandsaw must be connected to its own dedicated circuit; it should not share a circuit with any other machine. A standard 2-pole breaker is necessary for use with the Model G9963.

This bandsaw is not supplied with a power plug. We recommend “hard-wiring” the bandsaw to the power source, provided you place a locking shut off switch near the machine to disconnect the power.

Be sure that your particular electrical con- figuration complies with local and state codes. The best way to ensure compliance is to check with your local municipality or a licensed electrician.

24" & 27" Resaw Bandsaws

-5-

Image 7
Contents Models G3619/G3620/G9963/G9966 Resaw BandsawsPage Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For Bandsaws Model G3619 Model G9963 Circuit RequirementsModel G3620/G9966 440V Operation Typical plug configuration for Three-phase operationGrounding Extension Cords Commentary General InformationUnpacking Piece Inventory Site Considerations Clean UpBeginning AssemblyFence Dust Port To install the dust portTo mount the fence Identification AdjustmentsG3619/G3620 Blade Guides Guide PostBlade Guides G9963/G9966 Blade GuidesTo track the blade G3619/G3620 TrackingG9963/G9966 Tracking To center track your bladeSupport Bearings To adjust the support bearings behind the bladeTo center the support bearings laterally Guide Blocks To center the blade guard Blade Guard Table StopMake sure the bandsaw is unplugged Table Tilt To tilt the table Disconnect power to the bandsawTest Run To adjust the tensionBlade Tension To adjust the fence so it is parallel with the blade Fence Adjustment Blade LeadBlade Width OperationsBlade Selections Blade LengthBlade Care Tooth PitchBlade Breakage Blade Changes To perform ripping operations Ripping Stacked CutsTo complete a stacked cut Resawing To resaw lumber, follow the procedure belowLubrication MaintenanceBelts MiscellaneousPage Page 24 & 27 Resaw Bandsaws 24 & 27 Resaw Bandsaws Closure Machine Data Sheet G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 G3619/G3620 Frame Fence Rail Grizzly Model G9963/G9966 27 Bandsaw G9963/G9966 Arin g C o G9963/G9966 189 24 & 27 Resaw Bandsaws 8026 Hinge PIN Support Bearing Troubleshooting Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC