Grizzly G4186Z instruction manual Unpacking, Parts Inventory

Page 10

Unpacking

The bandsaw is shipped from the factory in a carefully packed crate. If you find the machine to be damaged after you have signed for delivery, and the truck and driver are already gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for inspection by the carrier or their agent. Without the packing materials, filing a freight claim can be difficult. If you need advice regarding this situa- tion, please call us immediately.

When you are completely satisfied with the con- dition of your shipment, you should inventory its parts.

The model G4186Z is a heavy machine (345 lbs. shipping weight). DO NOT over-exert yourself while unpacking or moving your machine – get assistance.

If moving this machine up or down stairs, the machine must be disman- tled and moved in smaller pieces. Make sure the stairs are capable of sup- porting the combined weight of the machine parts and the people mov- ing them.

Some die-cut metal parts may have sharp edges (“flashing”) on them after they are formed. Please examine the edges of all die- cut metal parts before handling them. Failure to do so could result in injury.

Parts Inventory

After all the parts have been removed from the crate, you should have:

¥Bandsaw Unit

¥Table

¥Table Bracket

¥Fence

¥Fence Rails

¥Miter Gauge

Hardware Bag

Qty

Cap Screws 1Ú4" - 20 x 11Ú2"

4

Fence Spacers

4

Table Insert

1

Table Trunnion Knobs

2

Lock Washers 3Ú8"

2

Roll Pin 3 x 10mm

1

Allen¨ Wrench 3mm

1

Allen¨ Wrench 4mm

1

Allen¨ Wrench 5mm

1

Round Guide Block

6

Setscrew 1Ú4"-20 x 1Ú4"

6

In the event that any parts are missing, we will be happy to replace them. Contact our Customer Service number for assistance. If any non-propri- etary parts such as nuts, bolts or washers are missing, we will be happy to replace these too, but for the sake of expediency, these items can be obtained at your local hardware store.

 

 

 

 

 

 

 

 

-8-

 

 

G4186Z 18" Bandsaw

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Professional Bandsaw Page Table Of Contents Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Bandsaws Circuit Requirements 220V Operation 110V OperationGrounding Wiring Diagram Extension CordsIntroduction Unpacking Parts InventoryClean Up Site ConsiderationsBeginning Assembly AssemblyTable and Support Bracket Table mounting components For quick fence removal and replacement Rails and FenceBlades To install the bladeTo remove the blade Adjustments ControlsBlade Tension To adjust the blade using center tracking Blade Tracking Wheel AlignmentPage Blade Guides Upper GuidesTable Adjustment To tilt the tableTable in maximum left tilt position Belt Tensioning To perform the alignmentDust Collection Changing SpeedsFence Adjustment Test Run Read the Ripping instructions before using the fencePre-Run Check OperationsAlways use a sharp, high-quality blade Bandsaw Blades Changing Blades Tension control knob G4186Z 18 BandsawG4186Z 18 Bandsaw To perform ripping operations Ripping Stacked CutsTo complete a stacked cut Cutting Curves Resawing Blade Width Minimum RadiiTo resaw lumber, follow the procedure below Resawing with an auxiliary fence G4186Z 18 BandsawBlade Lead To skew your fenceMiscellaneous MaintenanceLubrication BeltsMaintenance Notes Closure Troubleshooting Symptom Possible Cause Corrective ActionMachine Data G4186Z 18 Bandsaw G4186Z 18 Bandsaw Parts List DescriptionFence Tube G4186Z 18 Bandsaw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC
Top Page Image Contents