Global Machinery Company LS250TS2000W Switching on and off, Depth, Adjusting the blade angle

Page 14

Note. You can adjust the laser line so that it is just to one side of the cut or so that it is centred on the cut, depending on how you wish to use the laser line when cutting.

10.Tighten the 2 laser adjustment screws (11).

11.Check the adjustment and readjust if necessary

Switching on and off

 

 

 

e

1. To turn the table saw

 

 

 

ON, press the green push

 

 

button (fig e).

 

 

2. To turn the table saw OFF,

 

 

press the red push button

 

 

(fig f).

 

 

Note. This saw is fitted with

 

 

an electromagnetic switch.

 

 

 

 

In the case where the power

 

 

 

 

supply is turned off to the

 

f

saw, the saw must be turned

 

 

on by pressing the green ON

 

 

button after the power supply

 

 

is reconnected.

 

 

Adjusting the cutting

 

 

depth

 

 

Warning. The blade lock (24)

 

 

 

 

must be loosened before the

 

 

blade height is adjusted, and

g

re-tightened once the desired

 

setting is reached.

 

1. Set the saw blade to the

 

required cutting depth by

 

turning the blade height

 

handle (20) (fig g).

 

2. Turning the wheel anti-

 

clockwise increases the

 

cutting depth.

 

3.Turning the wheel clockwise decreases the cutting depth.

Adjusting the blade angle

1. Loosen the blade lock

 

h

(24) and turn the blade

angle wheel (21) until the

 

pointer (22) points to the

 

required angle on the scale

 

(23)(fig h).

2.The blade angle pointer

(22)can be adjusted when checking the accuracy of the blade angle. With the

power disconnected, place a set square against the saw blade. Adjust the blade angle wheel until the blade is parallel to the set square then move the pointer to 0° on the blade angle scale.

Using the rip fence

1.Use the rip fence when making longitudinal cuts.

2.The rip fence (14) can be fitted to either side of the table top (1). In order to use the rip fence scale (16), move the fence up to the blade and take a measurement on the scale. Now move the fence away from the blade. The difference in measurements will be equivalent to the width of cut. It is necessary to make a trial cut,

measure the workpiece

i

and re-adjust the rip

 

fence in order to establish

 

accurate datum levels.

 

3. Lift the rip fence locking

 

lever (15) and slide the

 

fence to the required

 

position (fig i).

 

4. Retighten the fence

 

 

locking lever (15).

 

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 2000W 250mm 10 Table Saw Contents Introduction SymbolsSpecifications Environmental protectionSafety rules for laser lights General safety instructionsAdditional safety rules for table saws Faulty saw blades have to be replaced immediately Wear goggles Wear earmuffs Wear a breathing mask UnpackingRequired Tools 1213 ComponentsAlready fitted on axle 18 17 1 Know your productTable top 819Assembly Stand set-upFitting the riving knife Laser assembly Fitting and adjusting Rear extension tableAttaching the height Adjustment handle Attaching the wheel axleFitting the blade guard Using the mitre gauge holderUsing the push stick holder Moving the saw Adjusting the laser lineFolding the stand Fig b Lift the blade guard off the riving knifeUsing the rip fence Switching on and offAdjusting the blade angle DepthPush sticks Using the mitre gaugeOperation KickbackCutting a narrow workpiece Tips to avoid kickbackMaking longitudinal cuts Making cross cuts Cutting an extremely narrow workpieceMaking bevel cuts Replacing the saw BladeChanging Batteries Laser generator Maintenance Power cord maintenanceCleaning General inspectionPage GMC Customer Assist
Top Page Image Contents