Global Machinery Company LS211 Mitre table locks, Bevel lock, Spindle lock button

Page 11

Mitre table locks

 

D

The mitre table locks (15)

 

are used to lock the table

 

at the desired mitre angle

 

(fig. D).

 

The mitre saw cuts from 0° to 45° both left and right. To adjust the mitre angle loosen the mitre table locks and

rotate the mitre table to the desired position. The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre angles.

WARNING. Be sure to tighten the mitre table locks before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury.

Bevel lock

 

The bevel lock (7) is used to

E

set the blade at the desired

 

bevel angle (fig. E). The

 

mitre saw bevel cuts from

 

0° to 45° to the left. To

 

adjust the bevel angle loosen

 

the bevel lock and adjust

 

the saw arm to the desired

 

bevel angle.

 

WARNING. Be sure to tighten the bevel lock before making a cut. Failure to do so could result in the saw arm moving during the cut and cause serious personal injury.

Spindle lock button

The spindle lock button (18)

F

prevents the blade in the

 

saw from rotating (fig. F).

 

Depress and hold the spindle

 

lock button while installing,

 

changing, or removing the

 

blade.

 

 

 

Rotating lower

 

G

blade guard

 

The rotating lower blade guard (5) provides protection from both sides of the blade (fig. G). It retracts over the upper blade guard (4) as the saw is lowered into the workpiece.

Turning on and off

H

1. To turn the saw on depress

 

and hold the on/off trigger

 

switch (16) (fig. H).

 

2. To turn the saw off release

 

the on/off trigger switch (16).

 

 

 

Turning on the REDEYE® laser line generator

The REDEYE® laser line

generator emits an intense I narrow beam of pure red

light to guide you as you cut. It improves operator cutting vision, enables faster set- up, increases accuracy and improves safety. To turn on the laser line press the laser light on/off switch (25) (fig. I). To turn off the laser

press the laser light on/off switch (25) one more time.

Setting the table square with the blade

1.Make sure that the electrical plug is removed from the power point.

2.Push the saw arm (1) down to its lowest position and engage the release knob (2) to hold the saw arm in the transport position.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 210mm 8 1/4 Compound Mitre Saw Contents Introduction Description of symbolsSpecifications Dear CustomerGeneral safety instructions Safety rules for laser lightsPage Additional safety rules for mitre saws Take additional care when trenching slotting Wear gloves when handling saw blades and rough materialsSaw blade fiited 6mm Hex Key Receipt holder AccessoriesBevel lock 6mm Hex key Bevel scale Mitre table Laser light Mitre scale On/off switchKnow your product Blade bolt coverRelease knob UnpackingTransportation Bench mountingSpindle lock button Setting the table square with the bladeMitre table locks Bevel lockLock 7 fig. K Setting the fence square with the tableLoosen the mitre locks Tighten the mitre locksBlade bolt fig. S Hold the rotating guard Up and press Changing a bladeRaise the saw arm 1 to its highest position Pull the rotating blade Guard 5 down thenBevel cut Operation Cross cutLoosen the bevel lock 7 and move the saw arm Compound mitre cutUsing the laser line generator Adjusting the laser lineGeneral inspection Maintenance Power cord maintenanceCleaning Page Page Save this Manual for future reference
Top Page Image Contents