Hitachi NV 65AF3 instruction manual Service and Repairs

Page 17

Nail stopper 1

3 Open the nail guide and remove dust.

 

 

Lubricate the sliding groove of the feeder and shafts.

 

 

Nail guide

 

 

Shaft

Nail stopper 2

Nail feeder

Nose

3. Inspect the Trigger

Clean the trigger sliding part.

Lubricate it with Hitachi pneumatic tool lubricant

Roll pin

Projection

Sliding part

4. Inspect the muffler

In case dust choke up the muffler or muffler is damaged,

Contact Hitachi for replacement.

Muffler

CAUTION

⬤Check that the nail feeder slides smoothly by pulling it with finger.

If not smooth, nails can be driven at an irregular angle and hurt someone.

5.Inspecting Magagine

1 DISCONNECT AIR HOSE

2 Clean the magazine. Remove dust of wooden chips which may have accumulated in the magazine.

6.Storing

•When not in use for an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust.

•Do not store the Nailer in a cold weather environment. Keep the Nailer in a warm area.

•When not in use, the Nailer should be stored in a warm and dry place. Keep out of reach children.

7.WARNING LABEL

Change the WARNING LABEL if missing or damaged.

A new WARNING LABEL is available from a Hitachi authorized service center.

8.Maintenance chart (See page 21)

9.Operator troubleshooting (See page 21)

SERVICE AND REPAIRS

WARNING

⬤Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer.

⬤Use only parts supplied or recommended by Hitachi for repair.

All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use.

NOTE:

Specifications are subject to change without any obligation on the part of HITACHI.

– 17 –

Page 16 Page 18
Image 17
Page 16 Page 18
Contents NV 65AF3 Contents Important Information Definitions of Signal WordsDo not Exceed 120 psi SafetySafety Stay Alert EMPLOYER’S ResponsibilitiesName of Parts OperationAccessories SpecificationsNail Selection MIN MAXBefore Operation ApplicationsWorking Environment AIR SupplyCold Weather Care LubricationTrigger Lock Air hoseLoading Nails Testing the NailerAdjusting AIR Pressure Plastic sheet collated nails Wire collated nailsLock lever Nailer OperationMethods of Operation Nose cap DrivingChanging the exhaust direction Adjusting the nailing depthCutting off the sheet Disconnect AIR Hose from NailerRead section titled Safety page 4 Maintenance and InspectionClearing a jam Inspect the feedersService and Repairs Operator troubleshooting Maintenance chartAction WHY HOW Problem Check Method Correction60 872-971 Retaining Ring for D3 Shaft 204

NV 65AF3 specifications

The Hitachi NV 65AF3 is a powerful, versatile tool designed for professionals in construction and woodworking, particularly in the framing and installation of materials. This pneumatic nailer is noteworthy for its combination of advanced technology and user-friendly features that enhance efficiency and productivity on the job site.

One of the stand-out features of the NV 65AF3 is its lightweight design. Weighing in at just under 4.4 pounds, the nailer allows for ease of handling over extended periods, reducing fatigue for users. This portability is complemented by its compact size, making it suitable for tight spaces where larger tools may prove cumbersome.

The NV 65AF3 utilizes a pneumatic power source, which means it requires an air compressor to operate. This not only provides a consistent power output but also allows the nailer to deliver impressive performance in terms of driving power. The tool is capable of driving nails ranging from 1-1/4 inches to 2-1/2 inches in length, making it suitable for applications such as framing, sheathing, and roofing.

Another key feature is its adjustable depth of drive. This functionality allows users to finely tune how deep the nails are driven into the material, ensuring precision and consistency in finishing work. The tool also includes a selective actuation switch that enables users to choose between sequential and contact firing modes. The sequential mode offers greater control, making it ideal for delicate tasks, while the contact mode allows for faster nailing in production environments.

A robust magazine holds up to 100 nails, enabling longer run times between reloads. The NV 65AF3’s rear exhaust directs air away from the user and work surface, keeping the workspace clean and safe.

Durability is another hallmark of the Hitachi NV 65AF3, with its rugged construction designed to withstand the rigors of job sites. The tool also features a rubber grip handle designed for comfort and stability during use.

In conclusion, the Hitachi NV 65AF3 is an exemplary pneumatic nailer, merging portability, power, and precision. Its user-centric design and durable build make it a reliable choice for contractors seeking a high-performance tool for a wide range of applications. Whether framing, roofing, or installing wood, the NV 65AF3 delivers the reliability and efficiency professionals demand.
Top Page Image Contents