AllTrade 835533 manual Compressor Features

Page 10

1

2

COMPRESSOR FEATURES

OIL LUBRICATION: Oil lubricated direct drive pump with cast-iron cylinder for durability.

OIL FILL SIGHT GLASS: Located on the face of the crankcase, the oil fill sight glass provides a convenient way to check the oil fill level within the pump. The oil level must be checked prior to each use to ensure proper fill level.

DO NOT OPERATE THE COMPRESSOR WITHOUT LUBRICANT, OR WITH LOW LUBRICATION LEVEL. THE MANUFACTURER IS NOT

RESPONSIBLE FOR DAMAGE CAUSED TO THE COMPRESSOR DUE TO OPERATION WITHOUT PROPER LUBRICATION.

3AUTOMATIC ON/OFF PRESSURE SWITCH: This compressor is equipped with an automatic ON/OFF pressure switch. The compressor will only run when the switch is in the ON/AUTO position. Once the tank has reached the desired preset pressure (“cut-out” pressure), the pump motor will automatically shut off. While the switch is in the ON/AUTO position, the pump motor will automatically turn back on once the pressure in the tank drops below the minimum preset pressure (“cut-in” pressure).

DO NOT LEAVE THE COMPRESSOR UNATTENDED WHILE THE POWER SWITCH IS IN THE ON/AUTO POSITION.

4AIR TANK PRESSURE GAUGE: The tank pressure gauge provides a reading of the air pressure inside of the compressor tank.

5PRESSURE REGULATOR: The regulator allows you to select the amount of air pressure that is output through the air hose into tools and accessories. Turn the pressure regulator knob clockwise to increase discharge pressure, and counter clockwise to decrease discharge pressure. Please refer to the air delivery requirements of your tools for the proper pressure settings.

NOTICE: Be careful not to overtighten pressure regulator knob when it “bottoms out” as this may damage pressure regulator.

6OUTLET PRESSURE GAUGE: The outlet pressure gauge provides a reading of the air pressure at the outlet side of the regulator. This pressure is controlled by the pressure regulator and is always less than or equal to the air tank pressure.

7SAFETY RELIEF VALVE: This compressor is equipped with a safety relief valve that is designed to prevent system failures by relieving pressure from the system when the air pressure reaches a predetermined level. The safety relief valve is preset by the manufacturer. DO NOT attempt to modify or remove the safety relief valve.

8AIR TANK DRAIN VALVE: Moisture is produced whenever air is compressed. It is critical to drain water from the air tank on this compressor frequently. If unit is used only occasionally, tank should be drained after each use and prior to the next use. To drain the tank, slowly open the tank drain fitting by turning clockwise. Once all moisture has drained out, close the fitting securely. NOTE: Air tank will not pressurize while drain valve is open.

9AIR INTAKE FILTER: This compressor is equipped with an externally accessible air intake filter that is designed to clean air coming into the pump. The filter element is easily removed for periodic cleaning. Use compressed air to blow loose dirt and debris from the paper filter element and reinstall. Replace paper filter element when necessary.

A dirty air filter will reduce air compressor performance and can lead to product failure.

10MANUAL THERMAL OVERLOAD SWITCH: The electric motor has a manual thermal overload protector. If the motor overheats for any reason, the thermal overload protector will shut off the motor. Turn pressure switch to the “off” position and wait for unit to cool before pushing the reset button and restarting the compressor. NOTICE: This air compressor is designed for household use only and is not intended to operate heavy-duty air tools. If your application’s demands exceed the capacity of this air compressor, a larger air compressor that is matched to your application is recommended. If the unit shuts down again, please call the consumer helpline at 1-800-423-3598 for assistance.

11CARRY HANDLE: Convenient handle for easy transport.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents AIR Compressor Table of Contents Specifications Introduction Safety AlertUnpacking & Inspection General Safety Warnings Safety WarningsDrain Liquid from AIR Tank Daily Installation and Location Grounding InstructionsExtension Cord Length Wire Size AWG Compressor FeaturesCompressor Features Compressor Features Pump Lubrication Assembly InstructionsAssembly Check Inspection CheckStartup Initial Setup / BREAK-IN ProcedureMaintenance OperationShutdown and Storage When Performing ANY Maintenance or ServiceMaintenance Checklist OIL ChangeChecking AIR Filter Element Checking Safety Relief ValveMoisture in Compressed AIR Troubleshooting Guide Or air accessory Motor/pressure switch releaseAir leaks from safety relief Air continues to leak atParts List Description QTY Parts Diagram Warranty Performance ONE Year Limited WarrantyExclusions Limitations on Warranty Disclaimers Warranty DisclaimersLimitation Of Liability Copyright 2006, Alltrade Tools LLC REV.1

835533 specifications

The AllTrade 835533 is a versatile and robust tool that stands out in the realm of multi-functional equipment. Tailored for both professional and DIY enthusiasts, this tool brings efficiency and convenience to a variety of tasks. One of its most defining features is its compact design, which allows for easy storage and portability. Weighing in at just a few pounds, the AllTrade 835533 is designed to be user-friendly, making it accessible for individuals of all skill levels.

At the heart of the AllTrade 835533 is its powerful motor that ensures seamless operation, whether you are drilling, cutting, or fastening. The tool supports a variable speed setting, allowing users to adjust the speed based on the specific application at hand. This feature is crucial for tasks that require precision, as it provides the flexibility needed for both delicate and heavy-duty applications.

Another significant characteristic of the AllTrade 835533 is its extensive compatibility with various attachments and accessories. This adaptability makes it an ideal choice for those looking to streamline their toolkit without sacrificing functionality. The tool is equipped with a quick-change chuck system, which enables users to switch out bits and accessories effortlessly, saving valuable time during projects.

The AllTrade 835533 also incorporates advanced safety features, including a built-in safety lock and ergonomic grip, ensuring that users can operate the tool with confidence. The ergonomic design minimizes user fatigue, making it suitable for prolonged use without discomfort.

In terms of technology, the AllTrade 835533 leverages modern engineering principles to enhance performance and durability. High-quality materials are used in its construction to withstand the rigors of regular use, ensuring that the tool remains a trusted companion for years to come.

The battery life of the AllTrade 835533 is another area where this tool excels. It is equipped with a long-lasting lithium-ion battery that charges quickly and retains power effectively, giving users the freedom to work without frequent interruptions.

In conclusion, the AllTrade 835533 is an exceptional tool that integrates power, versatility, and user-friendly features, making it an essential addition to any toolkit. With its impressive technology and thoughtful design, it is well-equipped to handle a wide range of tasks, solidifying its status as a reliable partner for both professionals and hobbyists alike.
Top Page Image Contents