AllTrade 835533 manual Extension Cord Length Wire Size AWG, Compressor Features

Page 8

DANGER

IMPROPER INSTALLATION OF THE GROUNDING PLUG CAN RESULT IN A RISK OF ELECTRIC SHOCK. IF REPAIR OR REPLACEMENT OF THE CORD IS NECESSARY, DO NOT CONNECT THE GROUNDING WIRE TO EITHER FLAT BLADE TERMINAL. THE WIRE WITH GREEN INSULATION WITH OR WITHOUT YELLOW STRIPES IS THE GROUNDING WIRE.

THIS PRODUCT IS FOR USE ON A NOMINAL 120-VOLT CIRCUIT AND HAS A THREE-PRONG GROUNDING PLUG THAT LOOKS LIKE THE PLUG ILLUSTRATED IN FIGURE 1. A TEMPORARY ADAPTER SIMILAR TO THE ADAPTER ILLUSTRATED IN SKETCH B AND C (SEE PAGE 5) MAY BE USED TO CONNECT THIS PLUG TO A 2-POLE RECEPTACLE AS SHOWN IN ILLUSTRATION B WHEN A PROPERLY GROUNDED OUTLET IS NOT AVAILABLE. THE TEMPORARY ADAPTER SHALL BE USED ONLY UNTIL A PROPERLY GROUNDED OUTLET (ILLUSTRATION A) IS INSTALLED BY A QUALIFIED ELECTRICIAN. TAB FOR GROUNDING SCREW, LUG, OR SIMILAR PART EXTENDING FROM THE ADAPTER MUST BE CONNECTED TO A PERMANENT GROUND SUCH AS A PROPERLY GROUNDED OUTLET BOX COVER. WHENEVER THE ADAPTER IS USED, IT MUST BE HELD IN PLACE BY A METAL SCREW.

THE USE OF A GFCI OUTLET IS STRONGLY RECOMMENDED. THE THIRD PRONG IS TO BE USED TO GROUND THE TOOL AND PROVIDE PROTECTION AGAINST ELECTRICAL SHOCK. NEVER REMOVE THE THIRD PRONG.

CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICEMAN IF THE GROUNDING INSTRUCTIONS ARE NOT COMPLETELY UNDERSTOOD, OR IF IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED. IF IT WILL NOT FIT THE OUTLET, HAVE THE PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

Extension Cords

THE USE OF AN EXTENSION CORD WITH THIS PRODUCT IS NOT RECOMMENDED as this can result in the loss of power to your air compressor which can prevent the motor from starting or running properly. This can also cause your fuse to blow or circuit breaker to trip. Running your air compressor on an undersized extension cord will cause permanent damage to internal switches and overheating of the electric motor. Use an additional length of air hose rather than an extension cord.

If you must use an extension cord, it should be plugged into a GFCI found in circuit boxes or protected receptacles. Use only UL listed 3-wire extension cords that have a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. Refer to the guide below for minimum gauge required for extension cords.

EXTENSION CORD LENGTH

WIRE SIZE (AWG)

Up to 25 Feet

14

26 to 50 Feet

12

51 to 100 Feet

10

Use only extension cords that are intended for outdoor use. These cords are identified by a marking “ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES, STORE INDOORS WHEN NOT IN USE.” Examine extension cord before use. DO NOT USE DAMAGED EXTENSION CORDS. Do not pull on cord to disconnect from receptacle; always disconnect by pulling on plug. Keep cord away from heat and sharp edges. Always shut OFF the air compressor AUTO/ON pressure switch before unplugging the compressor. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.

AVOID ELECTRICAL SHOCK HAZARD. NEVER USE THIS COMPRESSOR WITH A DAMAGED OR FRAYED

ELECTRICAL CORD OR EXTENSION CORD. INSPECT ALL ELECTRICAL CORDS REGULARLY.

NEVER USE IN OR NEAR WATER OR IN ANY ENVIRONMENT WHERE ELECTRIC SHOCK IS POSSIBLE. TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND.

DO NOT TOUCH THE PLUG WITH WET HANDS.

Guard against electrical shock. Avoid body contact with grounded services such as pipes, ovens, stoves, and refrigerator enclosures. If not properly grounded, this air compressor can incur the potential hazard of light trickle shock, particularly when used in damp locations. If electrical shock occurs, there is the potential of secondary hazard such as your hands contacting an operating air tool.

COMPRESSOR FEATURES

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents AIR Compressor Table of Contents Specifications Unpacking & Inspection Safety AlertIntroduction General Safety Warnings Safety WarningsDrain Liquid from AIR Tank Daily Installation and Location Grounding InstructionsExtension Cord Length Wire Size AWG Compressor FeaturesCompressor Features Compressor Features Assembly Instructions Assembly CheckPump Lubrication Inspection CheckInitial Setup / BREAK-IN Procedure MaintenanceStartup OperationWhen Performing ANY Maintenance or Service Maintenance ChecklistShutdown and Storage OIL ChangeMoisture in Compressed AIR Checking Safety Relief ValveChecking AIR Filter Element Troubleshooting Guide Motor/pressure switch release Air leaks from safety reliefOr air accessory Air continues to leak atParts List Description QTY Parts Diagram Exclusions ONE Year Limited WarrantyWarranty Performance Limitation Of Liability Warranty DisclaimersLimitations on Warranty Disclaimers Copyright 2006, Alltrade Tools LLC REV.1

835533 specifications

The AllTrade 835533 is a versatile and robust tool that stands out in the realm of multi-functional equipment. Tailored for both professional and DIY enthusiasts, this tool brings efficiency and convenience to a variety of tasks. One of its most defining features is its compact design, which allows for easy storage and portability. Weighing in at just a few pounds, the AllTrade 835533 is designed to be user-friendly, making it accessible for individuals of all skill levels.

At the heart of the AllTrade 835533 is its powerful motor that ensures seamless operation, whether you are drilling, cutting, or fastening. The tool supports a variable speed setting, allowing users to adjust the speed based on the specific application at hand. This feature is crucial for tasks that require precision, as it provides the flexibility needed for both delicate and heavy-duty applications.

Another significant characteristic of the AllTrade 835533 is its extensive compatibility with various attachments and accessories. This adaptability makes it an ideal choice for those looking to streamline their toolkit without sacrificing functionality. The tool is equipped with a quick-change chuck system, which enables users to switch out bits and accessories effortlessly, saving valuable time during projects.

The AllTrade 835533 also incorporates advanced safety features, including a built-in safety lock and ergonomic grip, ensuring that users can operate the tool with confidence. The ergonomic design minimizes user fatigue, making it suitable for prolonged use without discomfort.

In terms of technology, the AllTrade 835533 leverages modern engineering principles to enhance performance and durability. High-quality materials are used in its construction to withstand the rigors of regular use, ensuring that the tool remains a trusted companion for years to come.

The battery life of the AllTrade 835533 is another area where this tool excels. It is equipped with a long-lasting lithium-ion battery that charges quickly and retains power effectively, giving users the freedom to work without frequent interruptions.

In conclusion, the AllTrade 835533 is an exceptional tool that integrates power, versatility, and user-friendly features, making it an essential addition to any toolkit. With its impressive technology and thoughtful design, it is well-equipped to handle a wide range of tasks, solidifying its status as a reliable partner for both professionals and hobbyists alike.
Top Page Image Contents