AllTrade 835533 manual Drain Liquid from AIR Tank Daily

Page 6

DRAIN LIQUID FROM AIR TANK DAILY

•Use the drain valve located on the bottom of the lower air tank to drain. Failure to properly drain liquid from the tank will cause rust from moisture buildup, which weakens the tank and could lead to a violent tank explosion. Periodically inspect the tanks for unsafe conditions such as corrosion, cracked welds, and leaks.

•Release air slowly when draining moisture or depressurizing the air compressor. Fast moving air will stir up dust, dirt and debris that may be harmful.

RISK OF FIRE OR EXPLOSION

Avoid dangerous environments. Do not spray combustible/flammable liquid in a confined area. Spray area must be well ventilated. Do not smoke while spraying or spray where spark or flame is present. Arcing parts — keep compressor at least 20’ away from spraying area and all explosive vapors. Do not use compressor near gasoline or other flammable materials. Operate the air compressor in a well-ventilated area. Do not direct paint or other spray material towards the compressor. Read and follow all safety instructions for the material you are spraying. Be sure to use an approved respirator designed for use with your specific application.

RISK OF INJURY

Do not direct air stream at body. Use eye protection. Compressor starts automatically. Do not touch MOVING PARTS. Keep guards in place. Compressor does not supply breathable air.

DANGER

RISK OF BURSTING

•Do not adjust regulator to result in output pressure greater than marked maximum pressure of attachment. If a regulator has not been installed, use only attachment rated at 200 PSI or higher. Do not weld on or repair tank — A DAMAGED TANK MUST BE REPLACED IMMEDIATELY. Do not operate without proper safety valve in place.

•Never attempt to repair or make modifications to the tank or its attachments. Welding, drilling, or any other modifications may weaken the tank, which may result in damage from rupture or explosion. Never remove or attempt to adjust the pressure switch, safety valve, or other components that control tank pressure. Never substitute parts or attempt to alter the factory set operating pressures.

RISK OF ELECTRICAL SHOCK

Disconnect air compressor from power source before servicing. USE PROPERLY grounded ELECTRICAL CONNECTIONS — DO NOT use grounding adaptors. Do not use in wet or damp locations or expose to rain. Keep all connections dry and off the ground. Do not allow power cords to come into contact with water. Do not touch the plug with wet hands. Do not pull on the electrical cord to disconnect from the power outlet. Store air compressor indoors when not in use. Any electrical wiring or repairs performed on this air compressor should be done by authorized service personnel in accordance with federal and local electrical codes.

RISK TO BREATHING

•This air compressor is not designed, nor intended for the supply of breathable quality air. Air produced by this unit may contain carbon monoxide or other toxic vapors. Do not inhale air from the compressor or from a breathing device connected to it.

•Operate the air compressor in a well-ventilated area. Read and follow all safety instructions for the material you are spraying. Be sure to use an approved respirator designed for use with your specific application.

RISK OF BURNS

Touching exposed metal such as the compressor head or exhaust tube can result in serious burns. Keep hands and fingers away from exposed metal parts on air compressor during or immediately after operation. Air compressors generate significant heat during normal operation and will remain hot for some time after use. Do not reach around protective shrouds or attempt any maintenance until compressor has been allowed to cool.

RISK OF FLYING OBJECTS

Do not direct compressed air stream at people or pets. The powerful compressed air stream can damage exposed skin and easily propel loose dirt and other small objects at high-speed, resulting in serious injury. Always wear eye protection that meets ANSI Z28.1 specifications. Use only OSHA approved air blowguns. Never leave a pressurized air compressor unattended. Shut OFF air compressor and relieve pressure before performing maintenance or repairs. Do not move the air compressor while the air tank is pressurized. Never attempt to move the air compressor by pulling on the air hose.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents AIR Compressor Table of Contents Specifications Safety Alert IntroductionUnpacking & Inspection General Safety Warnings Safety WarningsDrain Liquid from AIR Tank Daily Installation and Location Grounding InstructionsExtension Cord Length Wire Size AWG Compressor FeaturesCompressor Features Compressor Features Pump Lubrication Assembly InstructionsAssembly Check Inspection CheckStartup Initial Setup / BREAK-IN ProcedureMaintenance OperationShutdown and Storage When Performing ANY Maintenance or ServiceMaintenance Checklist OIL ChangeChecking Safety Relief Valve Checking AIR Filter ElementMoisture in Compressed AIR Troubleshooting Guide Or air accessory Motor/pressure switch releaseAir leaks from safety relief Air continues to leak atParts List Description QTY Parts Diagram ONE Year Limited Warranty Warranty PerformanceExclusions Warranty Disclaimers Limitations on Warranty DisclaimersLimitation Of Liability Copyright 2006, Alltrade Tools LLC REV.1

835533 specifications

The AllTrade 835533 is a versatile and robust tool that stands out in the realm of multi-functional equipment. Tailored for both professional and DIY enthusiasts, this tool brings efficiency and convenience to a variety of tasks. One of its most defining features is its compact design, which allows for easy storage and portability. Weighing in at just a few pounds, the AllTrade 835533 is designed to be user-friendly, making it accessible for individuals of all skill levels.

At the heart of the AllTrade 835533 is its powerful motor that ensures seamless operation, whether you are drilling, cutting, or fastening. The tool supports a variable speed setting, allowing users to adjust the speed based on the specific application at hand. This feature is crucial for tasks that require precision, as it provides the flexibility needed for both delicate and heavy-duty applications.

Another significant characteristic of the AllTrade 835533 is its extensive compatibility with various attachments and accessories. This adaptability makes it an ideal choice for those looking to streamline their toolkit without sacrificing functionality. The tool is equipped with a quick-change chuck system, which enables users to switch out bits and accessories effortlessly, saving valuable time during projects.

The AllTrade 835533 also incorporates advanced safety features, including a built-in safety lock and ergonomic grip, ensuring that users can operate the tool with confidence. The ergonomic design minimizes user fatigue, making it suitable for prolonged use without discomfort.

In terms of technology, the AllTrade 835533 leverages modern engineering principles to enhance performance and durability. High-quality materials are used in its construction to withstand the rigors of regular use, ensuring that the tool remains a trusted companion for years to come.

The battery life of the AllTrade 835533 is another area where this tool excels. It is equipped with a long-lasting lithium-ion battery that charges quickly and retains power effectively, giving users the freedom to work without frequent interruptions.

In conclusion, the AllTrade 835533 is an exceptional tool that integrates power, versatility, and user-friendly features, making it an essential addition to any toolkit. With its impressive technology and thoughtful design, it is well-equipped to handle a wide range of tasks, solidifying its status as a reliable partner for both professionals and hobbyists alike.
Top Page Image Contents