AllTrade 835533 manual Initial Setup / BREAK-IN Procedure, Startup, Operation, Maintenance

Page 12

OPERATION

INITIAL SETUP / BREAK-IN PROCEDURE:

Do not attach air hose, air tools or other air accessories to the air outlet until break-in procedure has been successfully completed.

1.Read and understand the entire instruction manual, including all safety warnings before setting up air compressor.

2.Place air compressor on a flat, level surface.

3.Check oil fill level in crankcase and add oil as needed.

4.Turn the pressure regulator knob fully clockwise to open airflow from air outlet port.

Be careful not to overtighten pressure regulator knob when it “bottoms out” as this may damage pressure regulator.

5.Turn the power switch to the OFF position.

6.Plug power cord directly into a properly grounded power source of the correct voltage (see Grounding Instructions on page 5 of this instruction manual).

7.Open the tank drain valve to allow air to escape preventing air pressure buildup in the air tank.

8.Turn the compressor ON by moving the switch to the AUTO/ON position and run the air compressor for a period of 20 minutes to break-in the air pump.

9.With the compressor still running, at the end of the 20-minute break-in period, close the tank drain valve. The air compressor will build air pressure to the maximum preset pressure (“cut-out” pressure) and automatically shut off.

10.Slowly turn the tank drain valve to open airflow from drain and bleed off air from the air tank. The air compressor will automatically restart once the pressure in the air tank drops below the minimum preset pressure (“cut-in” pressure).

11.Turn the compressor off by moving the switch to the OFF position.

12.Release pressure from the system. Drain moisture from the air tank by slowly opening the air tank drain valve by turning clockwise. Tilt tank to remove all moisture. Once all the moisture has drained out, close the fitting securely.

NOTE: Air tank will not pressurize while drain valve is open.

13.Disconnect the power cord from the power outlet.

NOTE: Make sure the power switch is in the OFF position when connecting or disconnecting power cord from electrical outlet.

14.Your new air compressor is now ready to use.

STARTUP:

1.Before each startup, make sure the power switch is in the OFF position.

2.Place air compressor on a flat, level surface.

3.Check oil fill level in crankcase and add oil as needed.

4.Release pressure from the system. Drain moisture from the air tank by slowly opening the air tank drain valve by turning clockwise. Once all the moisture has drained out, close the fitting securely. NOTE: Air tank will not pressurize while drain valve is open.

5.Turn the pressure regulator knob fully counterclockwise to close airflow from air outlet port.

6.Attach air hose and accessories.

TOO MUCH AIR PRESSURE CAUSES A HAZARDOUS RISK OF BURSTING. CHECK THE MANUFACTURER’S MAXIMUM PRESSURE RATING FOR

AIR TOOLS AND ACCESSORIES. THE REGULATOR OUTLET PRESSURE MUST NEVER EXCEED THE MAXIMUM PRESSURE RATING.

7.Before connecting the compressor to the grounded outlet, check oil level, check for broken components and accessories, and check for damage to the hose.

8.Plug power cord directly into a properly grounded power source of the correct voltage (see Grounding Instructions on page 5 of this instruction manual).

9.Turn the compressor ON by moving the switch to the AUTO/ON position and allow the tank pressure to build. Once the air pressure reaches the maximum preset pressure (“cut-out” pressure) it will automatically shut off.

10.Slowly turn the pressure regulator knob clockwise to open airflow from air outlet port until desired output pressure is reached. NOTE: The air compressor will automatically restart once the pressure in the air tank drops below the minimum preset pressure (“cut-in” pressure).

MAINTENANCE

DISCONNECT AIR COMPRESSOR FROM POWER SOURCE AND BLEED OFF ALL AIR PRESSURE

BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents AIR Compressor Table of Contents Specifications Safety Alert IntroductionUnpacking & Inspection General Safety Warnings Safety WarningsDrain Liquid from AIR Tank Daily Installation and Location Grounding InstructionsExtension Cord Length Wire Size AWG Compressor FeaturesCompressor Features Compressor Features Assembly Instructions Assembly CheckPump Lubrication Inspection CheckInitial Setup / BREAK-IN Procedure MaintenanceStartup OperationWhen Performing ANY Maintenance or Service Maintenance ChecklistShutdown and Storage OIL ChangeChecking Safety Relief Valve Checking AIR Filter ElementMoisture in Compressed AIR Troubleshooting Guide Motor/pressure switch release Air leaks from safety reliefOr air accessory Air continues to leak atParts List Description QTY Parts Diagram ONE Year Limited Warranty Warranty PerformanceExclusions Warranty Disclaimers Limitations on Warranty DisclaimersLimitation Of Liability Copyright 2006, Alltrade Tools LLC REV.1

835533 specifications

The AllTrade 835533 is a versatile and robust tool that stands out in the realm of multi-functional equipment. Tailored for both professional and DIY enthusiasts, this tool brings efficiency and convenience to a variety of tasks. One of its most defining features is its compact design, which allows for easy storage and portability. Weighing in at just a few pounds, the AllTrade 835533 is designed to be user-friendly, making it accessible for individuals of all skill levels.

At the heart of the AllTrade 835533 is its powerful motor that ensures seamless operation, whether you are drilling, cutting, or fastening. The tool supports a variable speed setting, allowing users to adjust the speed based on the specific application at hand. This feature is crucial for tasks that require precision, as it provides the flexibility needed for both delicate and heavy-duty applications.

Another significant characteristic of the AllTrade 835533 is its extensive compatibility with various attachments and accessories. This adaptability makes it an ideal choice for those looking to streamline their toolkit without sacrificing functionality. The tool is equipped with a quick-change chuck system, which enables users to switch out bits and accessories effortlessly, saving valuable time during projects.

The AllTrade 835533 also incorporates advanced safety features, including a built-in safety lock and ergonomic grip, ensuring that users can operate the tool with confidence. The ergonomic design minimizes user fatigue, making it suitable for prolonged use without discomfort.

In terms of technology, the AllTrade 835533 leverages modern engineering principles to enhance performance and durability. High-quality materials are used in its construction to withstand the rigors of regular use, ensuring that the tool remains a trusted companion for years to come.

The battery life of the AllTrade 835533 is another area where this tool excels. It is equipped with a long-lasting lithium-ion battery that charges quickly and retains power effectively, giving users the freedom to work without frequent interruptions.

In conclusion, the AllTrade 835533 is an exceptional tool that integrates power, versatility, and user-friendly features, making it an essential addition to any toolkit. With its impressive technology and thoughtful design, it is well-equipped to handle a wide range of tasks, solidifying its status as a reliable partner for both professionals and hobbyists alike.
Top Page Image Contents