AllTrade 835533 manual Troubleshooting Guide

Page 15

 

TROUBLESHOOTING GUIDE

 

 

 

Problem Encountered

Possible Cause

Possible Solution

The compressor does not

Power cord not plugged in.

Plug cord into grounded outlet.

start or restart:

Motor/Pressure switch in

Move switch to AUTO position.

 

OFF position

Motor thermal overload switch has tripped.

Turn air compressor off, wait until the motor is cool, then press motor thermal overload (red) button firmly until click is heard.

 

Fuse blown or circuit breaker has

Replace fuse or reset circuit breaker.

 

tripped.

Check for proper fuse amperage.

 

 

 

 

Check for low voltage conditions.

 

 

Disconnect any other electrical appliances from circuit or

 

 

operate air compressor on its own branch circuit.

 

 

 

 

Wrong gauge wire or length of

Check chart in instruction manual for proper gauge wire

 

extension cord.

and cord length.

 

Air tank pressure exceeds motor/pressure

Motor will start automatically when air tank pressure drops

 

switch "cut-in" pressure.

below "cut-in" pressure of motor/pressure switch.

 

Pressure release valve on

Bleed the line by moving the switch to the OFF position.

 

motor/pressure switch has not

 

 

unloaded pump head pressure.

 

 

 

 

 

Defective motor, motor capacitor,

Contact Consumer Helpline at 1-800-423-3598.

 

motor/pressure switch.

 

The compressor motor stalls:

Overloaded motor.

Have a certified electrician check the motor and wiring.

 

 

Proceed with his or her recommendations.

 

Improper lubrication.

See LUBRICATION section in instruction manual.

 

Low oil level.

Check oil level and fill if necessary.

 

Defective check valve.

Replace check valve.

Excessively noisy operation:

Loose motor pulley or pump flywheel.

Tighten pulley and/or flywheel (where applicable).

 

Lack of oil in the pump crankcase.

Check oil level. If low, check for possible bearing damage.

 

 

Add correct amount of oil.

Carbon deposits on pistons or valves.

Remove cylinder head and inspect. Clean or replace parts as needed.

 

Bearing, piston or connecting rod

STOP THE COMPRESSOR! Contact Consumer Helpline at

 

failure.

1-800-423-3598.

 

Worn connecting rod.

Replace with new connecting rod.

 

Worn piston wrist pin bushing.

Remove piston/connecting rod assembly from the compressor

 

 

and inspect for excess wear. Replace worn parts as needed.

 

Worn bearings.

Replace worn bearings as needed.

 

 

NOTE: Dirty oil can cause accelerated wear.

 

 

Change oil frequently using recommended oil.

 

 

 

 

Noisy check valve.

Replace check valve.

When in the Start/Stop

Motor/Pressure switch does not shut

Move the motor/pressure switch to the OFF position. If the

option, motor runs

off motor when air compressor

motor does not shut off, unplug the air compressor. If the

continuously:

reaches "cut-out" pressure and safety

electrical contacts are welded together, replace the pressure

 

relief valve activates.

switch.

 

 

 

 

Air compressor is incorrectly sized.

Limit the air pressure to the capacity of the air compressor.

 

 

Either use a smaller tool or a larger air compressor.

Overheating:

Poor ventilation

Relocate the air compressor to an area with an ample supply

 

 

of cool, dry, and well-circulated air is available.

 

Dirty cooling fins.

Clean the outer surfaces of the cooling fins on the pump and

 

 

motor assembly.

 

 

 

Air continues to leak at motor/pressure switch release valve after motor stops:

Defective pilot valve, the check valve is Remove, clean or replace. stuck open.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents AIR Compressor Table of Contents Specifications Safety Alert IntroductionUnpacking & Inspection Safety Warnings General Safety WarningsDrain Liquid from AIR Tank Daily Grounding Instructions Installation and LocationCompressor Features Extension Cord Length Wire Size AWGCompressor Features Compressor Features Inspection Check Assembly InstructionsAssembly Check Pump LubricationOperation Initial Setup / BREAK-IN ProcedureMaintenance StartupOIL Change When Performing ANY Maintenance or ServiceMaintenance Checklist Shutdown and StorageChecking Safety Relief Valve Checking AIR Filter ElementMoisture in Compressed AIR Troubleshooting Guide Air continues to leak at Motor/pressure switch releaseAir leaks from safety relief Or air accessoryParts List Description QTY Parts Diagram ONE Year Limited Warranty Warranty PerformanceExclusions Warranty Disclaimers Limitations on Warranty DisclaimersLimitation Of Liability Copyright 2006, Alltrade Tools LLC REV.1

835533 specifications

The AllTrade 835533 is a versatile and robust tool that stands out in the realm of multi-functional equipment. Tailored for both professional and DIY enthusiasts, this tool brings efficiency and convenience to a variety of tasks. One of its most defining features is its compact design, which allows for easy storage and portability. Weighing in at just a few pounds, the AllTrade 835533 is designed to be user-friendly, making it accessible for individuals of all skill levels.

At the heart of the AllTrade 835533 is its powerful motor that ensures seamless operation, whether you are drilling, cutting, or fastening. The tool supports a variable speed setting, allowing users to adjust the speed based on the specific application at hand. This feature is crucial for tasks that require precision, as it provides the flexibility needed for both delicate and heavy-duty applications.

Another significant characteristic of the AllTrade 835533 is its extensive compatibility with various attachments and accessories. This adaptability makes it an ideal choice for those looking to streamline their toolkit without sacrificing functionality. The tool is equipped with a quick-change chuck system, which enables users to switch out bits and accessories effortlessly, saving valuable time during projects.

The AllTrade 835533 also incorporates advanced safety features, including a built-in safety lock and ergonomic grip, ensuring that users can operate the tool with confidence. The ergonomic design minimizes user fatigue, making it suitable for prolonged use without discomfort.

In terms of technology, the AllTrade 835533 leverages modern engineering principles to enhance performance and durability. High-quality materials are used in its construction to withstand the rigors of regular use, ensuring that the tool remains a trusted companion for years to come.

The battery life of the AllTrade 835533 is another area where this tool excels. It is equipped with a long-lasting lithium-ion battery that charges quickly and retains power effectively, giving users the freedom to work without frequent interruptions.

In conclusion, the AllTrade 835533 is an exceptional tool that integrates power, versatility, and user-friendly features, making it an essential addition to any toolkit. With its impressive technology and thoughtful design, it is well-equipped to handle a wide range of tasks, solidifying its status as a reliable partner for both professionals and hobbyists alike.
Top Page Image Contents