Woodstock W1755 owner manual Basic Controls, Table control locations Plunger

Page 22

W1755 6" Parallelogram Jointer

OPERATIONS

Basic Controls

This section covers the basic controls used during routine operations.

ON/OFF Switch (Figure 26): Starts and stops the motor. After the OFF paddle is pushed, the switch may need to be reset before the next operation by lifting the paddle and fully depressing the STOP button.

Table Movement: To move the infeed table, loosen the table lock (Figure 27), move the table with the table lever, then tighten the table lock. The infeed table will only move through the preset range of the positive stops. To adjust the infeed table positive stops, refer to Setting Infeed Table Height on Page 36.

The outfeed table is preset with positive stops so no range of movement is allowed (if it gets accidentally unlocked it will not move). To adjust the outfeed table positive stops, refer to Setting Outfeed Table Height on Page 35.

Fence Movement: The fence has a lock handle that keeps it in position (Figure 28). To move the fence, loosen the lock handle and slide the fence where needed.

Fence Tilting: The tilt lock (Figure 28) secures the fence at any position in the available range. The plunger locks into an indexing ring to easily set the fence tilt to 90°. Positive stops stop the fence at 45° inward and 45° out- ward, for common 45° bevel cuts. Even when the fence is resting against the positive stops, the tilt lock must be tightened before cutting.

START Button

OFF Button

Figure 26. Motor operation controls.

Table Locks
Outfeed Table	Infeed Table
Lever	Lever

Figure 27. Table control locations.

Plunger	Tilt Lock

Fence Tilt

Lever

Fence

Lock Handle

Figure 28. Fence lock, tilt lock, and stop

block locations.

-20-

Image 22

Contents Parallelogram Jointer Page Table of Contents Introduction Woodstock Technical SupportMachine Specifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Jointers Avoiding Potential Injuries Never surface plane without push Blocks110V/220V Operation Electrical SpecificationsElectrical Extension CordsItems Needed for Setup SetupUnpacking Inventory Power must not be connected to machine during setupAssembly Fasteners Qty Box 1 Figure QtyMachine Placement Cleaning Machine Assembly To assemble the jointer, do these stepsIf the pulleys are not aligned, follow Steps 10 Rolling the V-belt onto Cutterhead pulleyInstalling the belt guard Fence carriage mounted on Back of the jointer Failure to use a dust collection system can result Knife Setting Jig Dust Collection Short and long-term respiratory illnessTest Run To test run the jointer, do these stepsOperations GeneralBasic Controls Table control locations PlungerCorrect setting for grain Alignment 12 Min ⁄2 Min Stock Inspection RequirementsSquaring Stock Surface plane on the jointerRead and understand SAFETY, beginning on Surface PlaningEdge Jointing Typical edge jointing Operation PortionBevel Cutting To bevel cut on the jointer, do these stepsRabbet Cutting Typical rabbet cutting OperationMaintenance Schedule MaintenanceCleaning BeltsInspecting Knives ServiceTo inspect the knives, do these steps Adjusting/Replacing Knives Straightedge MethodTo adjust/replace the knives, do these steps First Time OnlyJack screw access hole To check the outfeed table parallelism, do these steps Checking/Adjusting Table ParallelismTo check the infeed table parallelism, do these steps Adjusting Table Parallelism To adjust the table parallelism, do these steps Eccentric bushing and set screw LocationSetting Outfeed Table Height To set the outfeed table height, do these stepsCalibrating Depth Scale Setting Infeed Table HeightTo calibrate the depth scale, do these steps To set the 90˚ fence stop, do these steps Setting Fence StopsTo set the 45˚ inward fence stop, do these steps To set the 45 outward fence stop, do these stepsBelt Replacement To replace the V-belts, do these stepsPulley Alignment To align the pulleys, do these stepsMotor wired for Electrical Components220V Wiring Diagram 110V Wiring DiagramSee Figure Troubleshooting Motor & ElectricalCutting Parts Stand Parts List PART# DescriptionJointer Breakdown Jointer Parts List XPB02M Labels/Cosmetic Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA