Woodstock W1755 owner manual Test Run, To test run the jointer, do these steps

Page 20

W1755 6" Parallelogram Jointer

Test Run

SETUP

Complete this process once you have familiarized yourself with all instructions in this manual.

To test run the jointer, do these steps:

1.Read the entire owner's manual first to make sure you are familiar with the safety and operation con- trols of this machine!

2.Make sure all tools and foreign objects have been removed from the machine.

3.Review Page 9 and connect your machine to the power source.

4.Lift the OFF paddle on the switch and press the red STOP button in all the way to make sure the switch is reset.

5.Turn the jointer ON.

—The jointer should run smoothly with little or no vibration.

—Immediately turn the jointer OFF if you suspect any problems, and refer to Page 42 to trouble- shoot/fix any problems before starting the jointer again. If the source of an unusual noise or vibra- tion is not readily apparent, contact our technical support for help at (360) 734-3482 or contact us online at tech-support@shopfox.biz.

6.Press the STOP paddle to turn the jointer OFF.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly and operation.

Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

-18-

Image 20

Contents Parallelogram Jointer Page Table of Contents Introduction Woodstock Technical SupportMachine Specifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Jointers Avoiding Potential Injuries Never surface plane without push BlocksElectrical Specifications Electrical110V/220V Operation Extension CordsUnpacking SetupItems Needed for Setup Power must not be connected to machine during setup Assembly Fasteners QtyInventory Box 1 Figure QtyMachine Placement Cleaning Machine Assembly To assemble the jointer, do these stepsIf the pulleys are not aligned, follow Steps 10 Rolling the V-belt onto Cutterhead pulley Installing the belt guard Fence carriage mounted on Back of the jointer Knife Setting Jig Dust CollectionFailure to use a dust collection system can result Short and long-term respiratory illnessTest Run To test run the jointer, do these stepsOperations GeneralBasic Controls Table control locations PlungerCorrect setting for grain Alignment 12 Min ⁄2 Min Stock Inspection RequirementsSquaring Stock Surface plane on the jointerRead and understand SAFETY, beginning on Surface PlaningEdge Jointing Typical edge jointing Operation PortionBevel Cutting To bevel cut on the jointer, do these stepsRabbet Cutting Typical rabbet cutting OperationMaintenance CleaningMaintenance Schedule BeltsTo inspect the knives, do these steps ServiceInspecting Knives Adjusting/Replacing Knives Straightedge MethodTo adjust/replace the knives, do these steps First Time OnlyJack screw access hole To check the infeed table parallelism, do these steps Checking/Adjusting Table ParallelismTo check the outfeed table parallelism, do these steps Adjusting Table Parallelism To adjust the table parallelism, do these steps Eccentric bushing and set screw LocationSetting Outfeed Table Height To set the outfeed table height, do these stepsTo calibrate the depth scale, do these steps Setting Infeed Table HeightCalibrating Depth Scale Setting Fence Stops To set the 45˚ inward fence stop, do these stepsTo set the 90˚ fence stop, do these steps To set the 45 outward fence stop, do these stepsBelt Replacement To replace the V-belts, do these stepsPulley Alignment To align the pulleys, do these stepsMotor wired for Electrical ComponentsSee Figure 110V Wiring Diagram220V Wiring Diagram Troubleshooting Motor & ElectricalCutting Parts Stand Parts List PART# DescriptionJointer Breakdown Jointer Parts List XPB02M Labels/Cosmetic Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA