Woodstock W1755 owner manual Table of Contents

Page 3

Table of Contents

INTRODUCTION

INTRODUCTION	2
Woodstock Technical Support	2
Controls and Features	4
SAFETY	5
Standard Safety Instructions	5
Additional Safety Instructions for Jointers...	7
Avoiding Potential Injuries	8
ELECTRICAL	9
110V/220V Operation	9
Extension Cords	9
Electrical Specifications	9
SETUP	10
Unpacking	10
Items Needed for Setup	10
Inventory	11
Machine Placement	12
Cleaning Machine	12
Assembly	13
Dust Collection	17
Knife Setting Jig	17
Test Run	18
OPERATIONS	19
General	19
Basic Controls	20
Stock Inspection & Requirements	21
Squaring Stock	22
Surface Planing	23
Edge Jointing	24
Bevel Cutting	25
Rabbet Cutting	26
MAINTENANCE	27
General	27
Cleaning	27
V-Belts	27
Lubrication	27
Maintenance Schedule	27

SERVICE	28
General	28
Inspecting Knives	28
Adjusting/Replacing Knives	29
Checking/Adjusting Table Parallelism	32
Setting Outfeed Table Height	35
Setting Infeed Table Height	36
Calibrating Depth Scale	36
Setting Fence Stops	37
V-Belt Replacement	38
Pulley Alignment	39
Electrical Components	40
110V Wiring Diagram	41
220V Wiring Diagram	41
Troubleshooting	42
PARTS	44
Stand Breakdown	44
Stand Parts List	45
Jointer Breakdown	46
Jointer Parts List	47
Labels/Cosmetic Parts	49
Warranty	50

SAFETY ELECTRICAL

SET UP OPERATIONS MAINTENANCE SERVICE

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

PARTS

Image 3

Contents Parallelogram Jointer Page Table of Contents Woodstock Technical Support IntroductionMachine Specifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Jointers Never surface plane without push Blocks Avoiding Potential InjuriesExtension Cords Electrical SpecificationsElectrical 110V/220V OperationSetup Items Needed for SetupUnpacking Box 1 Figure Qty Power must not be connected to machine during setupAssembly Fasteners Qty InventoryMachine Placement Cleaning Machine To assemble the jointer, do these steps AssemblyRolling the V-belt onto Cutterhead pulley If the pulleys are not aligned, follow Steps 10Installing the belt guard Fence carriage mounted on Back of the jointer Short and long-term respiratory illness Knife Setting JigDust Collection Failure to use a dust collection system can resultTo test run the jointer, do these steps Test RunGeneral OperationsTable control locations Plunger Basic ControlsStock Inspection Requirements Correct setting for grain Alignment 12 Min ⁄2 MinSurface plane on the jointer Squaring StockSurface Planing Read and understand SAFETY, beginning onTypical edge jointing Operation Portion Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingTypical rabbet cutting Operation Rabbet CuttingBelts MaintenanceCleaning Maintenance ScheduleService Inspecting KnivesTo inspect the knives, do these steps Straightedge Method Adjusting/Replacing KnivesFirst Time Only To adjust/replace the knives, do these stepsJack screw access hole Checking/Adjusting Table Parallelism To check the outfeed table parallelism, do these stepsTo check the infeed table parallelism, do these steps Adjusting Table Parallelism Eccentric bushing and set screw Location To adjust the table parallelism, do these stepsTo set the outfeed table height, do these steps Setting Outfeed Table HeightSetting Infeed Table Height Calibrating Depth ScaleTo calibrate the depth scale, do these steps To set the 45 outward fence stop, do these steps Setting Fence StopsTo set the 45˚ inward fence stop, do these steps To set the 90˚ fence stop, do these stepsTo replace the V-belts, do these steps Belt ReplacementTo align the pulleys, do these steps Pulley AlignmentElectrical Components Motor wired for110V Wiring Diagram 220V Wiring DiagramSee Figure Motor & Electrical TroubleshootingCutting Parts PART# Description Stand Parts ListJointer Breakdown Jointer Parts List XPB02M Labels/Cosmetic Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA