Woodstock W1755 owner manual Pulley Alignment, To align the pulleys, do these steps

Page 41

W1755 6" Parallelogram Jointer

Pulley Alignment

Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplanar) for opti- mum performance.

Each pulley can be adjusted by loosening the motor mount bolts, sliding the motor in or out, and retightening the fasteners to lock the motor pulley in place.

To align the pulleys, do these steps:

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Open the back cover and remove the belt guard.

3.Visually check the alignment of the two pulleys to make sure that they are aligned and that the V-belts are straight up and down (see Figure 67).

—If the pulleys are aligned, go to Step 8.

—If the pulleys are NOT aligned, do Steps 4–7.

4.Loosen the motor mount bolts shown in Figure 68.

5.Shift the motor horizontally as needed to align the motor pulley with the cutterhead pulley.

6.Tighten the motor mount bolts.

7.Close the back cover and reinstall the belt guard.

��

��

��

��

��

Figure 67. Pulleys aligned.

Figure 68. Motor mount bolts for adjusting

pulley alignment.

SERVICE

-39-

Image 41

Contents Parallelogram Jointer Page Table of Contents Woodstock Technical Support IntroductionMachine Specifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Jointers Never surface plane without push Blocks Avoiding Potential InjuriesElectrical Electrical Specifications110V/220V Operation Extension CordsUnpacking SetupItems Needed for Setup Assembly Fasteners Qty Power must not be connected to machine during setupInventory Box 1 Figure QtyMachine Placement Cleaning Machine To assemble the jointer, do these steps AssemblyRolling the V-belt onto Cutterhead pulley If the pulleys are not aligned, follow Steps 10Installing the belt guard Fence carriage mounted on Back of the jointer Dust Collection Knife Setting JigFailure to use a dust collection system can result Short and long-term respiratory illnessTo test run the jointer, do these steps Test RunGeneral OperationsTable control locations Plunger Basic ControlsStock Inspection Requirements Correct setting for grain Alignment 12 Min ⁄2 MinSurface plane on the jointer Squaring StockSurface Planing Read and understand SAFETY, beginning onTypical edge jointing Operation Portion Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingTypical rabbet cutting Operation Rabbet CuttingCleaning MaintenanceMaintenance Schedule BeltsTo inspect the knives, do these steps ServiceInspecting Knives Straightedge Method Adjusting/Replacing KnivesFirst Time Only To adjust/replace the knives, do these stepsJack screw access hole To check the infeed table parallelism, do these steps Checking/Adjusting Table ParallelismTo check the outfeed table parallelism, do these steps Adjusting Table Parallelism Eccentric bushing and set screw Location To adjust the table parallelism, do these stepsTo set the outfeed table height, do these steps Setting Outfeed Table Height To calibrate the depth scale, do these steps Setting Infeed Table Height Calibrating Depth Scale To set the 45˚ inward fence stop, do these steps Setting Fence StopsTo set the 90˚ fence stop, do these steps To set the 45 outward fence stop, do these stepsTo replace the V-belts, do these steps Belt ReplacementTo align the pulleys, do these steps Pulley AlignmentElectrical Components Motor wired forSee Figure 110V Wiring Diagram220V Wiring Diagram Motor & Electrical TroubleshootingCutting Parts PART# Description Stand Parts ListJointer Breakdown Jointer Parts List XPB02M Labels/Cosmetic Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA