Woodstock W1755 owner manual Labels/Cosmetic Parts

Page 51

W1755 6" Parallelogram Jointer

Labels/Cosmetic Parts

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again.

		��
	��	��
	��	��
		��
		��

��

��

��

��

��

��

��

REF	PART�#	DESCRIPTION
300	X1741302	CUTTERHEAD�GUARD�LABEL
301	X1741301	FENCE/CUTTERHEAD�LABEL
302	XLABEL-04	ELECTRICITY�LABEL
303	XLABEL-01	SAFETY�GLASSES�LABEL
304	X1755304	EAR�PROTECTION�LABEL
305	XLABEL-02	DISCONNENCT�POWER�LABEL
306	XLABEL-08	READ�MANUAL�LABEL

REF	PART�#	DESCRIPTION
307	X1741308	SHOP�FOX�NAMEPLATE
308	X1755308	MODEL�#�LABEL
309	X1755309	MACHINE�ID�LABEL
310	XPPAINT-1	"SF�WHITE"�TOUCH-UP�PAINT
311	XPPAINT-7	"SF�BLACK"�TOUCH-UP�PAINT
312	X1755312	DOUBLE�BLACK�STRIPE
313	X1755313	SINGLE�BLACK�STRIPE

PARTS

-49-

Image 51

Contents Parallelogram Jointer Page Table of Contents Woodstock Technical Support IntroductionMachine Specifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Jointers Never surface plane without push Blocks Avoiding Potential InjuriesExtension Cords Electrical SpecificationsElectrical 110V/220V OperationSetup Items Needed for SetupUnpacking Box 1 Figure Qty Power must not be connected to machine during setupAssembly Fasteners Qty InventoryMachine Placement Cleaning Machine To assemble the jointer, do these steps AssemblyRolling the V-belt onto Cutterhead pulley If the pulleys are not aligned, follow Steps 10Installing the belt guard Fence carriage mounted on Back of the jointer Short and long-term respiratory illness Knife Setting JigDust Collection Failure to use a dust collection system can resultTo test run the jointer, do these steps Test RunGeneral OperationsTable control locations Plunger Basic ControlsStock Inspection Requirements Correct setting for grain Alignment 12 Min ⁄2 MinSurface plane on the jointer Squaring StockSurface Planing Read and understand SAFETY, beginning onTypical edge jointing Operation Portion Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingTypical rabbet cutting Operation Rabbet CuttingBelts MaintenanceCleaning Maintenance ScheduleService Inspecting KnivesTo inspect the knives, do these steps Straightedge Method Adjusting/Replacing KnivesFirst Time Only To adjust/replace the knives, do these stepsJack screw access hole Checking/Adjusting Table Parallelism To check the outfeed table parallelism, do these stepsTo check the infeed table parallelism, do these steps Adjusting Table Parallelism Eccentric bushing and set screw Location To adjust the table parallelism, do these stepsTo set the outfeed table height, do these steps Setting Outfeed Table HeightSetting Infeed Table Height Calibrating Depth ScaleTo calibrate the depth scale, do these steps To set the 45 outward fence stop, do these steps Setting Fence StopsTo set the 45˚ inward fence stop, do these steps To set the 90˚ fence stop, do these stepsTo replace the V-belts, do these steps Belt ReplacementTo align the pulleys, do these steps Pulley AlignmentElectrical Components Motor wired for110V Wiring Diagram 220V Wiring DiagramSee Figure Motor & Electrical TroubleshootingCutting Parts PART# Description Stand Parts List Jointer Breakdown Jointer Parts List XPB02M Labels/Cosmetic Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA