Woodstock W1724, W1723 instruction manual Underside of planer table

Page 17

8.Place the block under the front of the head casting to either side of the depth stop.

9.Lower the cutterhead casting so the block barely touches the casting.

10.Remove the block and place it between the middle-rear of the cutterhead casting and the table. If there is a gap or it will not fit under the head casting, measure the difference with a feeler gauge. If this measurement is more than 0.002", then the table needs to be adjusted from front to back.

11.There are two methods to adjust the table on your planer. The first is for adjustments smaller than 0.016" and the second is for adjustments larger than 0.016".

To adjust the cutterhead casting less than 0.016", do these steps:

NOTE: This adjustment may require some trial and error and two people. One person holds the head casting in position with the two-by-four, and the other tightens the casting mounting screws shown in Figure 15.

1.Loosen the cutterhead casting mounting screws and lift/lower the casting with a long two-by-four until the table and the casting are parallel with each other.

2.Adjust each column on both sides until the cutterhead casting is properly set. While adjusting the columns, tighten each screw after each step to ensure accurate results.

To adjust the cutterhead casting more than 0.016", do these steps:

NOTE: The underside of the table has five sprockets and a chain. The four corner sprockets control cutterhead casting height, and the fifth sprocket (idler sprocket) controls chain tension. See Figure 16.

1.Loosen the two bolts on the idler sprocket bracket (as shown in Figure 16) to loosen the chain so that each sprocket can be rotated on its own. See Figure 17.

Figure 15. Cutterhead casting mounting screws.

Idler Sprocket

Bracket

Figure 16. Underside of planer table.

ADJUSTMENTS

 

Figure 17. Sprocket tooth-to-height ratio.

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Models Page Contents About Your New Planer Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing Safety FirstSafety Additional Safety Instructions for Planers 220V Operation ElectricalExtension Cords GroundingOverview AssemblyBox Contents Shop Preparation Cleaning PlanerTo mount the handwheel and crank, do these steps Stand W1723Handwheel To mount the extension rollers, do these steps Extension RollersSpiral Knife Alignment Tool W1724 Knife Setting Jig W1723To assemble the knife setting jig, do these steps Planer Overview AdjustmentsTo check the cutterhead-to-table alignment, do these steps Cutterhead AlignmentUnderside of planer table Adjustments Inspecting Knives W1723 Knife Replacement procedureTypical Shop FOX cutterhead Knife Replacement W1723Gib bolt tightening sequence Spiral knife system Knife Replacement W1724Twisting knife and aligning gib Feed Rollers Chip Breaker Chip breaker height adjustment Anti-Kickback Pawls To adjust the chip deflector, do these stepsChip Deflector Roller Spring Tension To adjust the roller spring tension, do these stepsTable Bed Rollers To adjust the table bed roller height, do these stepsOperations Always Wear Safety Goggles When Operating This machineTest Run Feed RateOperational Tips Only plane a clean workpieceSolutions Troubleshooting Planing ResultsMaintenance General CleaningGear box drain and fill plugs LubricationBelt Tension To adjust the belts, do these stepsSymptom Possible Cause Corrective Action Troubleshooting Machine OperationPlaner Accessories Maintenance Maintenance Description Maintenance Long T Allen Wrench 4MM Maintenance Angle 191⁄2 Long W1723 and W1724 15 Planer Wiring Diagram Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents