Delta D25235 029-2 How to Use Your Unit, Before Starting Break-in Procedure, How to Stop

Page 14
Pressure Release Valve

Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

Check Valve

Pressure Release Valve: The pressure release valve, located on the side of the pressure switch, is designed to automatically release compressed air

from the compressor head and the outlet tube when the air compressor reaches "cut-out" pressure or is

shut off. The pressure release valve allows the motor

to restart freely. When the motor stops running, air will be heard escaping from this valve for a few seconds. No air should be heard leaking when the motor is running, or continuous leaking after unit reaches "cut-out" pressure.

Air Intake Filter (not shown) This filter is designed to clean air coming into the pump. This filter must always be clean and ventilation openings free from obstructions. See "Maintenance".

How to Use Your Unit

How to Stop:

1.Set the On/Auto/Off lever to "OFF".

Before Starting

Break-in Procedure

Serious damage may result if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the On/Auto/Off lever is in the "OFF" position.

2.Recheck all wiring. Make sure wires are secure at all terminals connections. Make sure all contacts move freely and are not obstructed.

3.Open the globe valve fully to permit air to escape and prevent air pressure build up in the air tank during the break-in period. NOTE: The shut-off valve is not supplied with this unit. You must purchase the shut-off valve separately.

4.Move the On/Auto/Off lever to "ON/AUTO" position. The compressor will start.

5.Run the compressor for 20 minutes. Make sure the globe valve is open and there is minimal air pressure build-up in tank.

D25235

14-ENG

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Structioin N M Anual Safety Guidelines Definitions Hazard Attachments & Accessories Hazard What can Happen HOW to Prevent IT Fire, Inhalation, Damage to Vehicle Surfaces Glossary SpecificationsAccessories Duty CycleUnpacking AssemblyTools Required for Assembly To Add Oil To PumpAnchoring of the Air Compressor InstallationLocation of the Air Compressor Wiring Instructions Air Distribution SystemTypical Compressed AIR Distribution System Operation Know Your Air Compressor Description of OperationHow to Stop How to Use Your UnitBefore Starting Break-in Procedure How to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve Checking To Drain TankOil ChangingAdjusting Belt Tension Air Filter Inspection and ReplacementBelt Replacement Inspect Air Lines and Fittings for Leaks Motor Pulley/Flywheel AlignmentAir Compressor Pump Intake and Exhaust Valves Air compressor Head Bolts TorquingService and Adjustments To Replace or Clean Check ValveMotor Additional ServiceStorage Troubleshooting Problem Cause CorrectionPressure reading Minal box area 25-ENG D25235 AIR Compressor Diagram Parts List KEY Part Number DescriptionPump Diagram Not Shown Limited Warranty

D25235 029-2, DLKC6580V2 specifications

Delta DLKC6580V2 and D25235 029-2 represent significant advancements in the realm of industrial automation and control systems. These products harness cutting-edge technology to enhance operational efficiency, reliability, and flexibility across various applications.

The Delta DLKC6580V2 is a highly versatile motion control system designed for precision and performance. It boasts a robust architecture that supports a wide range of servo motors, making it ideal for applications requiring fine-tuned movements. One of the standout features of the DLKC6580V2 is its advanced control algorithms, which enable smooth and accurate motion, minimizing vibrations and ensuring high-quality outputs. Additionally, its real-time processing capabilities allow for rapid response and adjustments during operation, which is crucial in high-speed manufacturing environments.

Another key feature of the DLKC6580V2 is its integrated communication options. It supports multiple industrial protocols, including EtherCAT and CANopen, allowing seamless integration with various controllers and devices within an industrial setup. This flexibility enhances the overall system configuration and reduces downtime during installation and maintenance.

On the other hand, the D25235 029-2 is an innovative industrial power supply unit known for its reliability and efficiency. The D25235 series is designed to provide stable power under varying load conditions, making it an essential component for uninterrupted operations in critical applications. Its high efficiency minimizes energy consumption, contributing to lower operational costs and a reduced carbon footprint.

The D25235 029-2 features advanced protection mechanisms that safeguard against surges, overloads, and short circuits, ensuring long-term durability and reliability. The compact design of the unit also facilitates easy integration into existing systems, providing users with considerable versatility in installation.

Both the DLKC6580V2 and D25235 029-2 excel in delivering user-friendly interfaces, simplifying operation and configuration. With intuitive software tools, operators can quickly set up, monitor, and adjust settings, enhancing overall productivity.

In conclusion, Delta’s DLKC6580V2 and D25235 029-2 represent the pinnacle of innovation in industrial control and power supply systems. Their advanced features, exceptional performance, and robust technologies make them indispensable tools for modern manufacturing processes, offering businesses the ability to achieve higher efficiency and reliability in their operations.
Top Page Image Contents