Delta D25235 029-2, DLKC6580V2 instruction manual Glossary, Duty Cycle, Specifications, Accessories

Page 8

GLOSSARY

Become familiar with these terms before operating the unit.

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air deliv- ery.

PSIG: Pounds per square inch gauge; a unit of measure of pressure. Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety. Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level the motor will restart

automatically. The low pressure at which the motor automatically restarts is called "cut-in" pressure. Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor auto- matically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called "cut-out" pressure.

Branch Circuit: Circuit carrying elec- tricity from electrical panel to outlet. To Lock Out Power: Place a lock on the line power switch so no one else can turn on the power.

DUTY CYCLE

Air compressors should be operated on not more than a 50% duty cycle. This means an air compressor that pumps air more than 50% of one

hour is considered misuse, because the air compressor is undersized for the required air demand. Maximum compressor pumping time per hour is 30 minutes.

SPECIFICATIONS

Model No.

DLKC6580V2

Horsepower Peak

6.5

Voltage-Single Phase

240V/60Hz/1Ph

Minimum Branch Circuit Requirement

30 amps

*Fuse Type

Time Delay

Air Tank Capacity, Gallons

80 ASME, Vertical

Approximate Cut-in Pressure

145 PSIG

Approximate Cut-out Pressure

175 PSIG

SCFM @ 100 psig

16.9

SCFM @ 175 psig

16.0

*A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit on which the air compressor is operated. If compres- sor is connected to a circuit protected by fuses, use only time delay fuses. Time delay fuses should be marked "D" in Canada and "T" in the US.

ACCESSORIES

Accessories for this unit are available at the store the unit was purchased.

D25235

8-ENG

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Structioin N M Anual Safety Guidelines Definitions Hazard Attachments & Accessories Hazard What can Happen HOW to Prevent IT Fire, Inhalation, Damage to Vehicle Surfaces Specifications AccessoriesGlossary Duty CycleAssembly Tools Required for AssemblyUnpacking To Add Oil To PumpAnchoring of the Air Compressor InstallationLocation of the Air Compressor Wiring Instructions Air Distribution SystemTypical Compressed AIR Distribution System Operation Know Your Air Compressor Description of OperationHow to Stop How to Use Your UnitBefore Starting Break-in Procedure How to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain Tank OilChecking ChangingAdjusting Belt Tension Air Filter Inspection and ReplacementBelt Replacement Motor Pulley/Flywheel Alignment Air Compressor Pump Intake and Exhaust ValvesInspect Air Lines and Fittings for Leaks Air compressor Head Bolts TorquingService and Adjustments To Replace or Clean Check ValveMotor Additional ServiceStorage Troubleshooting Problem Cause CorrectionPressure reading Minal box area 25-ENG D25235 AIR Compressor Diagram Parts List KEY Part Number DescriptionPump Diagram Not Shown Limited Warranty

D25235 029-2, DLKC6580V2 specifications

Delta DLKC6580V2 and D25235 029-2 represent significant advancements in the realm of industrial automation and control systems. These products harness cutting-edge technology to enhance operational efficiency, reliability, and flexibility across various applications.

The Delta DLKC6580V2 is a highly versatile motion control system designed for precision and performance. It boasts a robust architecture that supports a wide range of servo motors, making it ideal for applications requiring fine-tuned movements. One of the standout features of the DLKC6580V2 is its advanced control algorithms, which enable smooth and accurate motion, minimizing vibrations and ensuring high-quality outputs. Additionally, its real-time processing capabilities allow for rapid response and adjustments during operation, which is crucial in high-speed manufacturing environments.

Another key feature of the DLKC6580V2 is its integrated communication options. It supports multiple industrial protocols, including EtherCAT and CANopen, allowing seamless integration with various controllers and devices within an industrial setup. This flexibility enhances the overall system configuration and reduces downtime during installation and maintenance.

On the other hand, the D25235 029-2 is an innovative industrial power supply unit known for its reliability and efficiency. The D25235 series is designed to provide stable power under varying load conditions, making it an essential component for uninterrupted operations in critical applications. Its high efficiency minimizes energy consumption, contributing to lower operational costs and a reduced carbon footprint.

The D25235 029-2 features advanced protection mechanisms that safeguard against surges, overloads, and short circuits, ensuring long-term durability and reliability. The compact design of the unit also facilitates easy integration into existing systems, providing users with considerable versatility in installation.

Both the DLKC6580V2 and D25235 029-2 excel in delivering user-friendly interfaces, simplifying operation and configuration. With intuitive software tools, operators can quickly set up, monitor, and adjust settings, enhancing overall productivity.

In conclusion, Delta’s DLKC6580V2 and D25235 029-2 represent the pinnacle of innovation in industrial control and power supply systems. Their advanced features, exceptional performance, and robust technologies make them indispensable tools for modern manufacturing processes, offering businesses the ability to achieve higher efficiency and reliability in their operations.
Top Page Image Contents