Electrical Requirements, Uplight | Emerson CF2500HTW01, CF2500S01

Electrical Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capa- ble of withstanding a load of at least 50 pounds.

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Mos outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electri- cian if in doubt.

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

!WARNING

To avoid fire, or shock, follow all wiring instructions carefully.

Any electrical work not described in these instructions should be done or approved by a licensed electrician.

The Emerson CF2500 Ceiling Fan is designed to be operated from a SR330 Remote Control, from a SW350 Wall Control with a SW375 Receiver, or from

SECTION A

Assembly Instructions

for Installing the CF2500 Ceiling Fan with a SW375 Receiver and a SR330 Remote Control or with a SW350 Wall Control

IF THE CF2500 CEILING FAN IS BEING INSTALLED WITH ANY OTHER CONTROL METHOD, SKIP SECTION A AND GO TO SECTION B TO BEGIN ASSEMBLY INSTRUCTIONS.

1.Cut the white, blue, and black wires about 3" above the motor coupling (Figure 1). Strip insula- tion 1/2" from end of wires and install a wire connector on the black wire; this wire will not be used. Remove the wire connectors from the red and brown wires.

INSULATE BLACK

WIRE USING WIRE

CONNECTOR

	BLACK WIRE
WHITE WIRE	BLUE WIRE
	REMOVE WIRE
3"	CONNECTORS
YELLOW	FROM RED AND
WIRE	BROWN WIRES
MOTOR	MOTOR COUPLING SLOT
COUPLING

Figure 1

2.Loosen the setscrew in the hanger ball, slide the ball down the downrod, and remove the clevis pin. Then slide the hanger ball off the downrod (Figure 2). Retain all parts for reinstallation in step 11.

CLEVIS PIN

other fan/light controls. There are no controls supplied with the ceiling fan. If you are going to control your ceiling fan with a SR330 Remote Control or with a SW350 Wall Control, proceed to “SECTION A”. If you are to control your ceiling fan in any other manner, proceed to “SECTION B”.

HANGER BALL

DOWNROD

Figure 2

SETSCREW

Uplight

This fan is supplied with a built-in uplight in the motor housing. This uplight does not have a built-in switch to turn it ON or OFF. A separate switch control must be used to operate the uplight. This can be done with a separate ON/OFF wall switch or one of the many Emerson Fan/Light Controls, such as the SW375 Receiver, SR330 Remote Control or SW95L Controls. The yellow lead supplied with this fan is the power lead for the uplight.

3.Push the wiring harness connector and the con- nector on the blue wire (both supplied with the SW375 Receiver and the SW350 Wall Control), and the connector on the uplight yellow lead assembly (supplied with the fan) through the downrod until they all extend about 4” out of the downrod (Figure 3).

4.Cut all wires approximately 3" from the end of the downrod’. Strip insulation 1/2" from end of wires.

4"	UPLIGHT YELLOW LEAD ASSEMBLY
	BLUE WIRE	CUT HERE
WIRING	DOWNROD	3"
HARNESS

4Figure 3