Final Assembly

NOTE: CEILING COVER,

SUPPLY WIRES AND

EMERSON FAN CONTROL

	FAN WIRES OMITTED	OUTLET
		BOX
	FOR CLARITY.

HANGER

BRACKET

LISTED OUTLET BOX

BLACK FAN WIRE

BLACKRED

GREEN WIRE (GROUND)

FROM HANGER

BRACKET

WHITE

GROUND

WIRE

LIGHT	BLACK
CONTROL	BLACK
	(HOT)
	TO 120
	VOLT
	SUPPLY
WHT.

Figure 28	HANGER BALL/
	DOWNROD ASSEMBLY

!WARNING

To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and the hanger bracket.

!WARNING

To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is ground- ed, contact a licensed electrician for advice, as it must be grounded for safe operation.

NOTE: If you are installing a SR330 Remote Control or a SW350 Wall Control to operate the fan and light, refer to the installation instructions and wiring diagrams shown in Section A of this Owner’s Manual.

22.For a wall control installation you will need a three-wire (with ground) conductor cable between the ceiling and wall outlet boxes. This will allow you to control the fan separately from the lights. Figure 29 is a basic wiring diagram that will con- trol the uplight and downlight on a switch and the fan on a separate control. Refer to the installation instructions and wiring diagrams supplied with the Emerson Fan Control Owner’s Manual.

a.Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or a wire with green colored insulation). Securely con- nect wires with wire connector supplied.

b.Securely connect the white wire from the downrod to the supply white (neutral) wire using wire connector supplied. Securely con- nect the black wire from the downrod to the supply black (hot) wire using wire connector supplied.

c.Cut terminal off of the yellow lead wire and strip insulation 1/2” from end of wire.

d.Securely connect the blue wire and yellow wire from the downrod to the supply red (hot) wire using wire connector (supplied). After connec- tions have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black, blue and yellow leads on the other side of the outlet box.

BLUE	GROUND	GROUND

GREEN WIRE (GROUND)	THREE - CONDUCTOR CABLE
	WITH GROUND BETWEEN
FROM HANGER BALL	CEILING AND WALL OUTLET
LISTED WIRE CONNECTOR (4)	BOXES

Figure 29

23.To complete the ceiling fan assembly, proceed to the “FINAL ASSEMBLY” section.

!WARNING

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.

1.Screw the two 1-1/4” threaded studs (provided) into the tapped holes in the hanger bracket.

2.Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 30).

3.Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs (supplied). (Figure 30.) Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the pipe.

	CEILING COVER
1-1/4"	LOCKWASHERS (2)
1-1/4"
THREADED
STUD

KNURLED KNOB

Figure 30

!WARNING

To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling.

4.Screw in three 40-watt (maximum) candelabra base lamps into the uplight sockets on top of the fan housing assembly.