RIDGID R4516 manual Features, Product Specifications

Page 10

FEATURES

PRODUCT SPECIFICATIONS

Blade Arbor	5/8 in.
Blade Diameter	10 in.
Blade Tilt	0˚ - 45˚
Rating	120 V~, 15 Amps, 60 Hz

No Load Speed	5,000 r/min. (RPM)
Cutting Depth at 0º:	3-1/4 in.
Cutting Depth at 45º:	2-3/8 in.

ANTI-KICKBACK

BLADE GUARD

RIP

PAWLS

MITER gauge

CORD

spreader/

RIVING KNIFE

FENCE

BEVEL

LOCKING

LEver

BEVEL

SCALE

STORAGE

BLADE

WRENCH

STORAGE

FRONT

RAIL

LOCKING

LEVER

HEIGHT/bevel

ADJUSTING

HANDWHEEL

SWITCH

ASSEMBLY

Fig. 2

Image 10

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbols Service Symbol Signal MeaningExtension Cords Speed and WiringElectrical Electrical ConnectionBevel Cut Anti-Kickback Pawls radial arm and table sawsArbor ChamferFeatures Product SpecificationsKnow Your Table SAW See FigureOperating Components Power SwitchSwitch KEY Removed To Turn Your SAW onCombination Framing Square Phillips ScrewdriverSQUAREFlat Blade Screwdriver Loose Parts Following items are included with your table sawUnpacking AssemblyTo install the Handle assembly Mounting HolesTo move the saw To Store the table saw AccessoriesRaising and Lowering the Handle MiterThroat Plate To remove/replace the Throat PlateTo Change Between a spreader and a riving knife UnlockedLarge Small Bladeblade Wrench Wrench To check SAW Blade installationTo Install the ANTI-KICKBACK Pawls and Blade Guard ANTI-KICKBACK PawlsScrew Spreader To Check and Align the spreader/ riving knife and Saw BladeFraming Square Causes of Kickback OperationApplications Avoiding KickbackFeatherboard HOW to Make a FeatherboardHOW to Mount a Featherboard Push BlocksCutting Tips Types of cuts See FigureTo Change Blade Angle To Adjust the Bevel indicatorTo Change Blade Depth To lock To unlock Bevel locking LeverTo use the Rip Fence To Set the rip fence Scale indicator to the BladeRear LIP Lock Knob Miter Gauge To use the miter gaugeTo use the sliding table extension Fence Sliding table Extension Locking Lever ScaleIf the distances are different Heeling paralleling the blade to the miter gauge grooveSee Figures 28 BoltsSee Figures 31 Switch KEY Switch in Locked PositionTo make a cross cut Cross CUT Place Left Hand on WorkpieceMaking a RIP cut Making a miter cutMaking a bevel rip cut Adjusting Handwheel Bevel Cross CUT BladeMaking a bevel cross cut Viewed from the FRONT, below the Table SAWBevel RIP CUT Making a compound bevel miter cutMaking a Large Panel cut Compound Bevel Miter CUTLarge Panel CUT RIP Fence Adjusting Handwheel SupportsMaking a NON-THROUGH cut Once all non-through cuts are completedNON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Once all dado cuts are completedThroat To replace the bladeWrench Large Riving Knife BladeSee Figures 45 Adjustment Bolt BladeTo SET the blade at 0 If the blade is not perfectly verticalTo Check the Alignment of the RIP Fence to the Blade To Adjust the miter gaugeAdjustable Stop ScrewGeneral MaintenanceAccessories LubricationTroubleshooting Problem Cause SolutionProblem Cause What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No R4516 Serial No