RIDGID manual Customer Service Information, Model No R4516 Serial No

Page 40

OPERATOR'S MANUAL

10 in. TABLE SAW

R4516

Customer Service Information

For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com.

The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided below. When ordering repair parts, always give the following information:

Model No.

R4516

 

Serial No.

 

 

987000-415

8-24-09 (REV:04)

40

Page 39 Page 40
Image 40
Page 39 Page 40
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbols Service Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Electrical ConnectionAnti-Kickback Pawls radial arm and table saws ArborBevel Cut ChamferFeatures Product SpecificationsKnow Your Table SAW See FigurePower Switch Switch KEY RemovedOperating Components To Turn Your SAW onCombination Framing Square Phillips ScrewdriverSQUAREFlat Blade Screwdriver Loose Parts Following items are included with your table sawAssembly To install the Handle assemblyUnpacking Mounting HolesTo Store the table saw Accessories Raising and Lowering the HandleTo move the saw MiterTo remove/replace the Throat Plate To Change Between a spreader and a riving knifeThroat Plate UnlockedTo check SAW Blade installation To Install the ANTI-KICKBACK Pawls and Blade GuardLarge Small Bladeblade Wrench Wrench ANTI-KICKBACK PawlsScrew Spreader To Check and Align the spreader/ riving knife and Saw BladeFraming Square Operation ApplicationsCauses of Kickback Avoiding KickbackHOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Push BlocksCutting Tips Types of cuts See FigureTo Adjust the Bevel indicator To Change Blade DepthTo Change Blade Angle To lock To unlock Bevel locking LeverTo use the Rip Fence To Set the rip fence Scale indicator to the BladeRear LIP To use the miter gauge To use the sliding table extensionLock Knob Miter Gauge Fence Sliding table Extension Locking Lever ScaleHeeling paralleling the blade to the miter gauge groove See Figures 28If the distances are different BoltsSwitch KEY Switch in Locked Position To make a cross cutSee Figures 31 Cross CUT Place Left Hand on WorkpieceMaking a RIP cut Making a miter cutAdjusting Handwheel Bevel Cross CUT Blade Making a bevel cross cutMaking a bevel rip cut Viewed from the FRONT, below the Table SAWMaking a compound bevel miter cut Making a Large Panel cutBevel RIP CUT Compound Bevel Miter CUTAdjusting Handwheel Supports Making a NON-THROUGH cutLarge Panel CUT RIP Fence Once all non-through cuts are completedNON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Once all dado cuts are completedTo replace the blade Wrench LargeThroat Riving Knife BladeAdjustment Bolt Blade To SET the blade at 0See Figures 45 If the blade is not perfectly verticalTo Adjust the miter gauge AdjustableTo Check the Alignment of the RIP Fence to the Blade Stop ScrewMaintenance AccessoriesGeneral LubricationTroubleshooting Problem Cause SolutionProblem Cause Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No R4516 Serial No
Top Page Image Contents