RIDGID MS1065LZA manual Warranty, DAY Satisfaction Guarantee Policy, Additional Limitations

Page 31

WARRANTY

RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY

Proof of purchase must be presented when requesting warranty service.

Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID®, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID® Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.

90-DAY SATISFACTION GUARANTEE POLICY

During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this RIDGID® Hand Held and Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product. The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period.

WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY

This warranty on RIDGID® Hand Held and Stationary Power Tools covers all defects in workmanship or materials and nor- mal wear items such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in this RIDGID® tool for three years following the purchase date of the tool. Warranties for other RIDGID® products may vary.

HOW TO OBTAIN SERVICE

To obtain service for this RIDGID® tool you must return it; freight prepaid, or take it in to an authorized service center for RIDGID® branded hand held and stationary power tools. You may obtain the location of the authorized service center nearest you by calling (toll free) 1-866-539-1710 or by log- ging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option, at no charge to you.

WHAT IS NOT COVERED

This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for RIDGID® branded hand held and stationary power tools. Consumable accessories provided with the tool such as, but not limited to, blades, bits and sand paper are not covered.

RIDGID®, INC. AND ONE WORLD TECHNOLOGIES, INC. MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied warran- ties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One World Technologies, Inc. and RIDGID®, Inc. are not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

One World Technologies, Inc.

P.O. Box 35, Hwy. 8

Pickens, SC 29671

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceExtension Cords ElectricalDouble Insulation Electrical ConnectionAnti-Kickback Pawls radial arm and table saws Glossary of TermsProduct Specifications FeaturesBlade Wrench / Storage Area Know Your Compound Miter SAWAMP Motor Bevel Lock KnobTools Needed SAW Blade Loose Parts ListBlade Wrench Trace Holes AT These Locations For Hole Pattern SAW Base AssemblyUnpacking Mounting HolesDust BAG Work Clamp Dust GuideDust BAG Work ClampMovement To Install / Replace the BladeTable Extension Table Extension Socket Head Washer ScrewCAP Head Screws Miter Fence Cutting a Slot in the Zero Clearance Throat PlateSee Figures 13 Squaring the SAW Blade to the FenceSee Figures 19 Squaring the Blade to the Miter TableBevel Lock Knob Miter Fence Blade Broken Laser Line Aligning the Laser Guide LineApplications OperationCutting with Your Compound Miter SAW Straight Cross CUT Work Clamp To Cross CUTSee Figures 24 To Bevel CUTBevel CUT Work Clamp Compound Miter CUT Work Clamp To Compound Miter CUT45 X 45 Compound Miter CUT Long Workpiece Workpiece Supports To Support Long WorkpiecesCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Laying Molding Flat on the Miter Table Cutting Crown Molding Right Wrong Cutting Warped Material Clamping Wide Workpieces See Figures 31Bevel Pivot Adjustment AdjustmentsTo Adjust the Laser Guide Pivot Adjustments Travel Pivot AdjustmentLubrication MaintenanceGeneral Maintenance Batteries Battery Compartment Negative Laser Guide SlotHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyMS1065LZA Customer Service Information
Top Page Image Contents