RIDGID MS1065LZA manual General Maintenance, Lubrication, Changing the Batteries in the Laser

Page 30

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

When replacing the batteries, the laser guide should be thoroughly cleaned. Use a soft paintbrush, or similar device, to remove all sawdust and debris.

After cleaning the laser guide and replacing batteries, align the two slots and secure the battery compartment to laser guide using the screw. Tighten screw securely.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrica- tion is required.

WARNING:

To ensure safety and reliability, all repairs should be performed by a qualified service technician at an authorized service center to avoid risk of personal injury.

CHANGING THE BATTERIES IN THE LASER

See Figure 36.

Unplug the saw.

Rotate and hold lower blade guard up.

Using the hex key (1/16 in.) provided, loosen and remove the screw from the battery compartment then separate the cover from the laser guide.

Lower the blade guard.

Remove the three button cell batteries from the battery compartment.

NOTE: Replace the batteries with button cell batteries that have a rating of 1.5 volt and 100 mAh (milliampere hour) minimum (number 76 series or equivalent).

m n

BATTERIES

BATTERY

COMPARTMENT

NEGATIVE (–)

LASER

GUIDE

SLOT

BATTERY

COMPARTMENT

SCREW

Fig. 36

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningElectrical Connection ElectricalDouble Insulation Extension CordsGlossary of Terms Anti-Kickback Pawls radial arm and table sawsFeatures Product SpecificationsBevel Lock Knob Know Your Compound Miter SAWAMP Motor Blade Wrench / Storage AreaTools Needed Loose Parts List SAW BladeBlade Wrench Mounting Holes AssemblyUnpacking Trace Holes AT These Locations For Hole Pattern SAW BaseWork Clamp Dust GuideDust BAG Dust BAG Work ClampTable Extension Socket Head Washer Screw To Install / Replace the BladeTable Extension MovementCutting a Slot in the Zero Clearance Throat Plate CAP Head Screws Miter FenceSquaring the SAW Blade to the Fence See Figures 13Squaring the Blade to the Miter Table See Figures 19Bevel Lock Knob Miter Fence Blade Aligning the Laser Guide Line Broken Laser LineOperation ApplicationsCutting with Your Compound Miter SAW To Cross CUT Straight Cross CUT Work ClampTo Bevel CUT See Figures 24Bevel CUT Work Clamp To Compound Miter CUT Compound Miter CUT Work ClampTo Support Long Workpieces 45 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Number of Sides Cutting Crown Molding Laying Molding Flat on the Miter TableSee Figures 31 Cutting Warped MaterialClamping Wide Workpieces Right WrongPivot Adjustments Travel Pivot Adjustment AdjustmentsTo Adjust the Laser Guide Bevel Pivot AdjustmentBatteries Battery Compartment Negative Laser Guide Slot MaintenanceGeneral Maintenance LubricationWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information MS1065LZA

MS1065LZA specifications

The RIDGID MS1065LZA is a high-performance miter saw designed for professional contractors and serious DIY enthusiasts alike. Known for its precision and versatility, this tool stands out in its category due to several key features and advanced technologies that enhance its functionality and ease of use.

One of the primary characteristics of the MS1065LZA is its robust 15-amp motor, which delivers a formidable 5,200 RPM. This powerful motor ensures smooth, consistent cuts through various materials including hardwood, softwood, and composite materials. Coupled with a 10-inch carbide-tipped blade, the saw is capable of making precise crosscuts and miter cuts, offering users the ability to tackle an array of projects with confidence.

The MS1065LZA includes an adjustable miter range of 0 to 60 degrees to the right and 0 to 52 degrees to the left, allowing for increased flexibility when making angled cuts. The dual bevel feature enables users to easily create bevel cuts in both directions without having to flip the material, which saves time and improves efficiency. The miter saw is also equipped with positive stops at common angles, ensuring quick and accurate settings.

Another notable feature is the innovative laser lighting system, which provides a clear cutting line for improved accuracy. This integrated laser guide helps users align their cuts precisely, reducing the likelihood of errors and waste material. Additionally, the transparent blade guard offers enhanced visibility while keeping the user safe during operation.

The MS1065LZA boasts a large, sturdy base that adds stability and supports larger workpieces, accommodating various project sizes. Its lightweight design enhances portability, making it easier to transport between job sites. The saw also comes with a dust bag that helps minimize mess, keeping the workstation cleaner while cutting.

In terms of user-friendly features, the large ergonomic handle enhances comfort during extended use. The saw is designed with easy-to-read scales and a simple locking mechanism for effortless adjustments. With its combination of power, precision, and practicality, the RIDGID MS1065LZA stands out as a top choice for professionals seeking reliable performance and exceptional results in their woodworking projects.
Top Page Image Contents