RIDGID MS1065LZA manual Squaring the SAW Blade to the Fence, See Figures 13

Page 18

ASSEMBLY

SQUARING THE SAW BLADE TO THE FENCE

See Figures 13 - 18.

Unplug the saw.

Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

Loosen the miter lock handle approximately one-half turn.

Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0°.

Release the miter lock plate and securely tighten the miter lock handle.

Lay a framing square flat on the miter table. Place one leg of the square against the fence. Slide the other leg of the square against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

The edge of the square and the saw blade should be parallel as shown in figure 14.

If the front or back edge of the saw blade angles away from the square as shown in figures 15 and 16, adjust- ments are needed.

CAUTION:

To keep from losing control of the unit, steady the base with one hand while loosening the two bolts with the other hand.

With the unit securely resting on a large stable surface, tilt the unit by lifting up on one side of the base.

Using a combination wrench, loosen the two cap head screws on the underside of the saw table.

Return the saw to its normal resting position. Make sure the miter lock knob is loose but do not release the miter lock plate.

Use the miter saw knob to move the table so that the blade contacts the full length of the framing square. Turn the miter lock knob clockwise to lock saw square to the fence.

Tilt the unit by lifting up on one side of the base and tighten cap head screws.

Recheck blade squareness to fence and readjust if necessary.

Your saw has several scale indicators. After squaring adjust- ments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 18.

MITER

FENCE

BLADE

FRAMING

MITER SQUARE

TABLE

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

Fig. 16

INDICATOR

SCREW

BEVEL

SCALE

SCALE

INDICATOR

INDICATOR

POINT

Fig. 17

INDICATOR

SCREWMITER SCALE

SCALE

INDICATOR

Fig. 18

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningElectrical Connection ElectricalDouble Insulation Extension CordsGlossary of Terms Anti-Kickback Pawls radial arm and table sawsFeatures Product SpecificationsBevel Lock Knob Know Your Compound Miter SAWAMP Motor Blade Wrench / Storage AreaTools Needed Loose Parts List SAW BladeBlade Wrench Mounting Holes AssemblyUnpacking Trace Holes AT These Locations For Hole Pattern SAW BaseWork Clamp Dust GuideDust BAG Dust BAG Work ClampTable Extension Socket Head Washer Screw To Install / Replace the BladeTable Extension MovementCutting a Slot in the Zero Clearance Throat Plate CAP Head Screws Miter FenceSquaring the SAW Blade to the Fence See Figures 13Squaring the Blade to the Miter Table See Figures 19Bevel Lock Knob Miter Fence Blade Aligning the Laser Guide Line Broken Laser LineOperation ApplicationsCutting with Your Compound Miter SAW To Cross CUT Straight Cross CUT Work ClampTo Bevel CUT See Figures 24Bevel CUT Work Clamp To Compound Miter CUT Compound Miter CUT Work ClampTo Support Long Workpieces 45 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Number of Sides Cutting Crown Molding Laying Molding Flat on the Miter TableSee Figures 31 Cutting Warped MaterialClamping Wide Workpieces Right WrongPivot Adjustments Travel Pivot Adjustment AdjustmentsTo Adjust the Laser Guide Bevel Pivot AdjustmentBatteries Battery Compartment Negative Laser Guide Slot MaintenanceGeneral Maintenance LubricationWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information MS1065LZA

MS1065LZA specifications

The RIDGID MS1065LZA is a high-performance miter saw designed for professional contractors and serious DIY enthusiasts alike. Known for its precision and versatility, this tool stands out in its category due to several key features and advanced technologies that enhance its functionality and ease of use.

One of the primary characteristics of the MS1065LZA is its robust 15-amp motor, which delivers a formidable 5,200 RPM. This powerful motor ensures smooth, consistent cuts through various materials including hardwood, softwood, and composite materials. Coupled with a 10-inch carbide-tipped blade, the saw is capable of making precise crosscuts and miter cuts, offering users the ability to tackle an array of projects with confidence.

The MS1065LZA includes an adjustable miter range of 0 to 60 degrees to the right and 0 to 52 degrees to the left, allowing for increased flexibility when making angled cuts. The dual bevel feature enables users to easily create bevel cuts in both directions without having to flip the material, which saves time and improves efficiency. The miter saw is also equipped with positive stops at common angles, ensuring quick and accurate settings.

Another notable feature is the innovative laser lighting system, which provides a clear cutting line for improved accuracy. This integrated laser guide helps users align their cuts precisely, reducing the likelihood of errors and waste material. Additionally, the transparent blade guard offers enhanced visibility while keeping the user safe during operation.

The MS1065LZA boasts a large, sturdy base that adds stability and supports larger workpieces, accommodating various project sizes. Its lightweight design enhances portability, making it easier to transport between job sites. The saw also comes with a dust bag that helps minimize mess, keeping the workstation cleaner while cutting.

In terms of user-friendly features, the large ergonomic handle enhances comfort during extended use. The saw is designed with easy-to-read scales and a simple locking mechanism for effortless adjustments. With its combination of power, precision, and practicality, the RIDGID MS1065LZA stands out as a top choice for professionals seeking reliable performance and exceptional results in their woodworking projects.
Top Page Image Contents