RIDGID MS1065LZA manual To Support Long Workpieces

Page 25

OPERATION

Align the cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C-clamp to secure the workpiece when possible.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

Grasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the workpiece.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

TO SUPPORT LONG WORKPIECES

See Figure 29.

Long workpieces need extra supports. Supports should be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and work table during the cutting operation. Use the work clamp or a C-clamp to secure the workpiece.

45° X 45° COMPOUND MITER CUT

Fig. 28

LONG WORKPIECE

WORKPIECE SUPPORTS

Fig. 29

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceDouble Insulation ElectricalElectrical Connection Extension CordsAnti-Kickback Pawls radial arm and table saws Glossary of TermsProduct Specifications FeaturesAMP Motor Know Your Compound Miter SAWBevel Lock Knob Blade Wrench / Storage AreaTools Needed SAW Blade Loose Parts ListBlade Wrench Unpacking AssemblyMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseDust BAG Dust GuideWork Clamp Dust BAG Work ClampTable Extension To Install / Replace the BladeTable Extension Socket Head Washer Screw MovementCAP Head Screws Miter Fence Cutting a Slot in the Zero Clearance Throat PlateSee Figures 13 Squaring the SAW Blade to the FenceSee Figures 19 Squaring the Blade to the Miter TableBevel Lock Knob Miter Fence Blade Broken Laser Line Aligning the Laser Guide LineApplications OperationCutting with Your Compound Miter SAW Straight Cross CUT Work Clamp To Cross CUTSee Figures 24 To Bevel CUTBevel CUT Work Clamp Compound Miter CUT Work Clamp To Compound Miter CUT45 X 45 Compound Miter CUT Long Workpiece Workpiece Supports To Support Long WorkpiecesCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Laying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialSee Figures 31 Right WrongTo Adjust the Laser Guide AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentGeneral Maintenance MaintenanceBatteries Battery Compartment Negative Laser Guide Slot LubricationDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredMS1065LZA Customer Service Information

MS1065LZA specifications

The RIDGID MS1065LZA is a high-performance miter saw designed for professional contractors and serious DIY enthusiasts alike. Known for its precision and versatility, this tool stands out in its category due to several key features and advanced technologies that enhance its functionality and ease of use.

One of the primary characteristics of the MS1065LZA is its robust 15-amp motor, which delivers a formidable 5,200 RPM. This powerful motor ensures smooth, consistent cuts through various materials including hardwood, softwood, and composite materials. Coupled with a 10-inch carbide-tipped blade, the saw is capable of making precise crosscuts and miter cuts, offering users the ability to tackle an array of projects with confidence.

The MS1065LZA includes an adjustable miter range of 0 to 60 degrees to the right and 0 to 52 degrees to the left, allowing for increased flexibility when making angled cuts. The dual bevel feature enables users to easily create bevel cuts in both directions without having to flip the material, which saves time and improves efficiency. The miter saw is also equipped with positive stops at common angles, ensuring quick and accurate settings.

Another notable feature is the innovative laser lighting system, which provides a clear cutting line for improved accuracy. This integrated laser guide helps users align their cuts precisely, reducing the likelihood of errors and waste material. Additionally, the transparent blade guard offers enhanced visibility while keeping the user safe during operation.

The MS1065LZA boasts a large, sturdy base that adds stability and supports larger workpieces, accommodating various project sizes. Its lightweight design enhances portability, making it easier to transport between job sites. The saw also comes with a dust bag that helps minimize mess, keeping the workstation cleaner while cutting.

In terms of user-friendly features, the large ergonomic handle enhances comfort during extended use. The saw is designed with easy-to-read scales and a simple locking mechanism for effortless adjustments. With its combination of power, precision, and practicality, the RIDGID MS1065LZA stands out as a top choice for professionals seeking reliable performance and exceptional results in their woodworking projects.
Top Page Image Contents