RIDGID MS1065LZA manual Aligning the Laser Guide Line, Broken Laser Line

Page 20

ASSEMBLY

DANGER:

Laser radiation. Avoid direct eye contact with light source.

ALIGNING THE LASER GUIDE LINE

See Figure 22.

The laser guide will generate a laser line on the work surface when the saw blade is spinning. The laser line will appear as a broken line on the workpiece when the blade assembly is in the uppermost position and the motor switch is activated. This broken line will let you see your mark and your laser guide line at the same time, and will assist you in lining up your mark for more accurate cutting of the workpiece.

Align the laser line and your mark with the blade at the uppermost position. Once both lines are in alignment, do not move the workpiece until after you have finished cutting.

As the blade assembly is lowered toward the workpiece, the broken line will become solid.

Follow the directions below for using the laser guide:

Removing Your Mark:

Position the laser line on the left edge of your mark on the work surface in order to remove the mark.

To Cut Your Mark:

Position the laser line near or over your mark on the work surface in order to cut the mark.

To Leave Your Mark:

Position the laser line near the right edge of your mark on the work surface in order to leave the mark.

After you have become familiar with using the laser guide, you will be able to remove, cut, or leave your mark on the work surface. Practice will teach you the correct position for aligning the laser line with your mark. To adjust the position of the laser line, see the Adjustments section of this manual.

BROKEN

LASER

LINE

Fig. 22

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OPERATOR’S Manual Table of Contents Introduction Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningElectrical Double InsulationElectrical Connection Extension CordsGlossary of Terms Anti-Kickback Pawls radial arm and table sawsFeatures Product SpecificationsKnow Your Compound Miter SAW AMP MotorBevel Lock Knob Blade Wrench / Storage AreaTools Needed Blade Wrench Loose Parts ListSAW Blade Assembly UnpackingMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseDust Guide Dust BAGWork Clamp Dust BAG Work ClampTo Install / Replace the Blade Table ExtensionTable Extension Socket Head Washer Screw MovementCutting a Slot in the Zero Clearance Throat Plate CAP Head Screws Miter FenceSquaring the SAW Blade to the Fence See Figures 13Bevel Lock Knob Miter Fence Blade Squaring the Blade to the Miter TableSee Figures 19 Aligning the Laser Guide Line Broken Laser LineCutting with Your Compound Miter SAW OperationApplications To Cross CUT Straight Cross CUT Work ClampBevel CUT Work Clamp To Bevel CUTSee Figures 24 To Compound Miter CUT Compound Miter CUT Work ClampTo Support Long Workpieces 45 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsPitch Number of Sides COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Cutting Crown Molding Laying Molding Flat on the Miter TableCutting Warped Material Clamping Wide WorkpiecesSee Figures 31 Right WrongAdjustments To Adjust the Laser GuidePivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentMaintenance General MaintenanceBatteries Battery Compartment Negative Laser Guide Slot LubricationWarranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information MS1065LZA

MS1065LZA specifications

The RIDGID MS1065LZA is a high-performance miter saw designed for professional contractors and serious DIY enthusiasts alike. Known for its precision and versatility, this tool stands out in its category due to several key features and advanced technologies that enhance its functionality and ease of use.

One of the primary characteristics of the MS1065LZA is its robust 15-amp motor, which delivers a formidable 5,200 RPM. This powerful motor ensures smooth, consistent cuts through various materials including hardwood, softwood, and composite materials. Coupled with a 10-inch carbide-tipped blade, the saw is capable of making precise crosscuts and miter cuts, offering users the ability to tackle an array of projects with confidence.

The MS1065LZA includes an adjustable miter range of 0 to 60 degrees to the right and 0 to 52 degrees to the left, allowing for increased flexibility when making angled cuts. The dual bevel feature enables users to easily create bevel cuts in both directions without having to flip the material, which saves time and improves efficiency. The miter saw is also equipped with positive stops at common angles, ensuring quick and accurate settings.

Another notable feature is the innovative laser lighting system, which provides a clear cutting line for improved accuracy. This integrated laser guide helps users align their cuts precisely, reducing the likelihood of errors and waste material. Additionally, the transparent blade guard offers enhanced visibility while keeping the user safe during operation.

The MS1065LZA boasts a large, sturdy base that adds stability and supports larger workpieces, accommodating various project sizes. Its lightweight design enhances portability, making it easier to transport between job sites. The saw also comes with a dust bag that helps minimize mess, keeping the workstation cleaner while cutting.

In terms of user-friendly features, the large ergonomic handle enhances comfort during extended use. The saw is designed with easy-to-read scales and a simple locking mechanism for effortless adjustments. With its combination of power, precision, and practicality, the RIDGID MS1065LZA stands out as a top choice for professionals seeking reliable performance and exceptional results in their woodworking projects.
Top Page Image Contents