RIDGID MS1290LZ1 manual Assembly, Unpacking, Mounting Holes

Page 15

ASSEMBLY

UNPACKING

This product requires assembly.

WARNING:

Carefully lift saw from the carton by the carrying handle and the saw base, and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

This saw has been shipped with the saw arm secured in the down position. To release the saw arm, push down on the top of the saw arm, cut the tie-wrap, and pull out on the depth guide.

Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap and/or depth guide.

Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

Do not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has influ- enced the settings, refer to specific procedures explained in this manual.

If any parts are damaged or missing, please call 1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing, do not oper- ate this tool until the damaged or missing parts are replaced. Failure to do so could result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create acces- sories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

Do not connect to power supply until assembly is complete. Failure to comply could result in acciden- tal starting and possible serious personal injury.

WARNING:

Do not start the miter saw without checking for interference between the saw blade and the sliding miter fences. Damage could result to the blade if it strikes the miter fence during operation of the saw.

WARNING:

Always make sure the compound miter saw is securely mounted to a workbench or an approved workstand. Failure to heed this warning can result in serious personal injury.

MOUNTING HOLES

See Figure 8.

The compound miter saw should be mounted to a firm supporting surface such as a workbench, mounting board, or leg stand. The saw base has eight mounting holes: four large bolt holes (B) and four small screw holes (A). If using bolts, they should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench or other mounting surface. Tighten all four bolts or screws securely. Do not use screws if mounting to a leg stand.

The hole pattern for mounting to a workbench is shown in figure 8. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor before operating.

TRACE HOLES AT THESE

B

A

A

B

 

 

 

 

 

 

LOCATIONS FOR HOLE PATTERN

 

 

 

 

 

(A - SCREWS AND B - BOLTS)

 

 

 

 

 

 

A

 

 

A

 

 

B

 

 

 

 

 

 

B

 

 

 

 

 

MOUNTING

 

 

SAW BASE

 

 

SURFACE

Fig. 8

 

 

 

 

 

 

 

15

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OPERATOR’S Manual Introduction Table of ContentsGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Product Specifications FeaturesBevel Lock Lever Know Your Compound Miter SAW12 IN. Blade AMP MotorMiter Thumbwheel Switch TriggerMiter Lock Lever Miter ScalePhillips Screwdriver Framing Square Tools NeededRatchet Combination SquareLoose Parts Dust BAGFlat Head Socket CAP Screw Assembly UnpackingMounting Holes Depth Guide Using the Depth GuideLocking / Unlocking the SAW ARM SAW ARMWork Clamp Installing the Dust BAGInstalling the Work Clamp Dust BAG Frame Guide Exhaust PortWasher HEX Boltinner Blade Washer with Installing / Replacing the BladeBlade Outer Blade Washer LoosenBroken RED Line Mounting the Exactline Laser GuideAligning the Laser Guide Line LaserCentering the SAW Blade Between the Slide Bars Removing / Replacing the Zero CLEAR- Ance Throat PlateSee Figures 20 Adjusting the Miter Lock LeverSquaring the SAW Blade to the Fence See Figures 18View of Blade Square with Fence Miter Scale Indicator FigSee Figures 25 Adjusting the Bevel Lock LeverAdjusting the Bevel Pivot Travel Pivot AdjustmentSliding Miter Fence IndicatorSquaring the Blade to the Miter Table See Figures 28Operation ApplicationsCutting with Your Sliding Compound Miter SAW To Slide CUT See Figures 32Slide CUT Slide SAW ARM Forward then Push Down Back To Miter CUT / Cross CUT See Figures 34Work Clamp Cross CUT Miter CUT Bevel CUT Clamp Lock PIN Scale Indicator BevelTo Bevel CUT See Figures 36Compound Miter CUT To Compound Miter CUTLong Workpiece Supporting Long WorkpiecesClamping Wide Workpieces See Figures 40Depth Guide CUT These Grooves With SAW Using AN Auxiliary FenceRough Cutting a Dado See Figures 43COMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Side Inside Corner Fence Cutting Crown MoldingLaying Molding Flat on the Miter Table CeilingUsing a Crown Molding Support JIG Making a Crown Molding Support JIGCrown Molding JIG Lubrication MaintenanceGeneral Maintenance Cutting Warped MaterialBrush CAP Belt Cover Brush ReplacementAdjusting Socket Head Screw Motor Belt TensionKEY Changing the BatteriesDo not attempt to activate the laser Laser Guide Screws Aperture Cover KEYMiter Saw Utility Vehicle AccessoriesHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No MS1290LZ1 Serial No Customer Service Information

MS1290LZ1 specifications

The RIDGID MS1290LZ1 is a powerful miter saw designed for both professional tradespeople and avid DIYers, providing exceptional versatility, precision, and ease of use. With its robust features and innovative technologies, this miter saw stands out in the crowded market of power tools.

One of the standout features of the MS1290LZ1 is its powerful 15-amp motor, which generates an impressive 4,000 RPM. This high-speed operation allows for quick and clean cuts through various materials, including hardwood, softwood, and composites. Capable of making both bevel and miter cuts, the saw offers a cutting capacity of up to 12 inches, making it suitable for a range of applications, from framing to crown molding.

The MS1290LZ1 is equipped with a dual bevel system, allowing users to make beveled cuts to the left and right with ease. This means that operators can achieve precise angles without the need to flip or reposition their workpieces, significantly enhancing efficiency. The saw features a generous cutting capacity of 0 to 50 degrees for miter cuts on both sides, enabling a wide variety of projects with intricate angles.

Another notable characteristic of this miter saw is its advanced laser guide system. This technology projects an accurate line of cut directly onto the material, ensuring maximum precision. The adjustable laser can be aligned with the blade for improved accuracy, reducing the likelihood of errors. Additionally, the MS1290LZ1 includes a built-in work light that illuminates the cutting area, providing visibility in low-light environments.

The saw's ergonomic design enhances user comfort during operation. Equipped with a sturdy and lightweight chassis, the MS1290LZ1 is easy to transport, making it an excellent choice for on-site jobs. The handle features a comfortable grip, allowing for extended use without causing fatigue. Moreover, the saw includes a dust collection port that helps maintain a clean workspace by minimizing sawdust and debris.

In conclusion, the RIDGID MS1290LZ1 miter saw combines power, precision, and user-friendly features, making it an ideal tool for both novice and experienced users. With its powerful motor, dual bevel capabilities, advanced laser guide, and ergonomic design, this miter saw offers the versatility and performance needed to tackle any cutting task with confidence. Whether you're framing a house, crafting custom furniture, or working on detailed trim, the MS1290LZ1 is equipped to handle the job efficiently and accurately.
Top Page Image Contents