RIDGID How to Change Blade and Replace Batteries on Miter Saw
Page 37

MAINTENANCE

CHANGING THE BATTERIES

See Figure 52.

Unplug the saw.

WARNING:

Failure to unplug the saw could result in accidental starting causing possible serious personal injury.

Remove the laser guide from the saw. Lay laser guide on a flat surface with the two phillips screws facing upward. Remove the screws and separate the laser guide cover from the laser guide support.

Remove the three button cell batteries using a non-conduc- tive device such as a toothpick.

NOTE: Replace the batteries with button cell batteries that have a rating of 1.5 volt and 100 mah (milliampere hour) minimum (Number 76 series or equivalent).

When replacing the batteries, the laser guide should be thoroughly cleaned. Use a soft paintbrush, or similar device, to remove all sawdust and debris.

Do not attempt to activate the laser.

The laser is activated by means of a centrifugal switch only while the saw motor is running and the laser guide is mounted on the saw.

After cleaning laser guide and replacing batteries, secure laser guide cover to laser guide support using the two phillips head screws. For proper assembly, be sure to align the key on the laser guide cover with the key slot in the laser guide support. Tighten screws securely.

NOTE: Aperture in laser guide cover must be aligned with aperture in laser guide support.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

LASER GUIDE

DANGER: Laser radiation when open and interlock defeated. AVOID DIRECT EYE EXPOSURE.

SCREWS

APERTURE

LASER GUIDE

COVER

KEY

KEY

SLOT

BATTERIES

LASER GUIDE

NEGATIVE (–)

SUPPORT

 

APERTURE

Fig. 52

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications Features12 IN. Blade Know Your Compound Miter SAWAMP Motor Bevel Lock LeverMiter Lock Lever Switch TriggerMiter Scale Miter ThumbwheelRatchet Tools NeededCombination Square Phillips Screwdriver Framing SquareDust BAG Loose PartsFlat Head Socket CAP Screw Unpacking AssemblyMounting Holes Locking / Unlocking the SAW ARM Using the Depth GuideSAW ARM Depth GuideInstalling the Work Clamp Installing the Dust BAGDust BAG Frame Guide Exhaust Port Work ClampBlade Installing / Replacing the BladeOuter Blade Washer Loosen Washer HEX Boltinner Blade Washer withAligning the Laser Guide Line Mounting the Exactline Laser GuideLaser Broken RED LineCentering the SAW Blade Between the Slide Bars Removing / Replacing the Zero CLEAR- Ance Throat PlateSquaring the SAW Blade to the Fence Adjusting the Miter Lock LeverSee Figures 18 See Figures 20View of Blade Square with Fence Miter Scale Indicator FigAdjusting the Bevel Pivot Adjusting the Bevel Lock LeverTravel Pivot Adjustment See Figures 25Squaring the Blade to the Miter Table IndicatorSee Figures 28 Sliding Miter FenceApplications OperationCutting with Your Sliding Compound Miter SAW See Figures 32 To Slide CUTSlide CUT Slide SAW ARM Forward then Push Down Back See Figures 34 To Miter CUT / Cross CUTWork Clamp Cross CUT Miter CUT To Bevel CUT Scale Indicator BevelSee Figures 36 Bevel CUT Clamp Lock PINCompound Miter CUT To Compound Miter CUTClamping Wide Workpieces Supporting Long WorkpiecesSee Figures 40 Long WorkpieceRough Cutting a Dado Using AN Auxiliary FenceSee Figures 43 Depth Guide CUT These Grooves With SAWCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Side Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceMaking a Crown Molding Support JIG Using a Crown Molding Support JIGCrown Molding JIG General Maintenance MaintenanceCutting Warped Material LubricationAdjusting Socket Head Screw Brush ReplacementMotor Belt Tension Brush CAP Belt CoverDo not attempt to activate the laser Changing the BatteriesLaser Guide Screws Aperture Cover KEY KEYMiter Saw Utility Vehicle AccessoriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1290LZ1 Serial No Customer Service Information

MS1290LZ1 specifications

The RIDGID MS1290LZ1 is a powerful miter saw designed for both professional tradespeople and avid DIYers, providing exceptional versatility, precision, and ease of use. With its robust features and innovative technologies, this miter saw stands out in the crowded market of power tools.

One of the standout features of the MS1290LZ1 is its powerful 15-amp motor, which generates an impressive 4,000 RPM. This high-speed operation allows for quick and clean cuts through various materials, including hardwood, softwood, and composites. Capable of making both bevel and miter cuts, the saw offers a cutting capacity of up to 12 inches, making it suitable for a range of applications, from framing to crown molding.

The MS1290LZ1 is equipped with a dual bevel system, allowing users to make beveled cuts to the left and right with ease. This means that operators can achieve precise angles without the need to flip or reposition their workpieces, significantly enhancing efficiency. The saw features a generous cutting capacity of 0 to 50 degrees for miter cuts on both sides, enabling a wide variety of projects with intricate angles.

Another notable characteristic of this miter saw is its advanced laser guide system. This technology projects an accurate line of cut directly onto the material, ensuring maximum precision. The adjustable laser can be aligned with the blade for improved accuracy, reducing the likelihood of errors. Additionally, the MS1290LZ1 includes a built-in work light that illuminates the cutting area, providing visibility in low-light environments.

The saw's ergonomic design enhances user comfort during operation. Equipped with a sturdy and lightweight chassis, the MS1290LZ1 is easy to transport, making it an excellent choice for on-site jobs. The handle features a comfortable grip, allowing for extended use without causing fatigue. Moreover, the saw includes a dust collection port that helps maintain a clean workspace by minimizing sawdust and debris.

In conclusion, the RIDGID MS1290LZ1 miter saw combines power, precision, and user-friendly features, making it an ideal tool for both novice and experienced users. With its powerful motor, dual bevel capabilities, advanced laser guide, and ergonomic design, this miter saw offers the versatility and performance needed to tackle any cutting task with confidence. Whether you're framing a house, crafting custom furniture, or working on detailed trim, the MS1290LZ1 is equipped to handle the job efficiently and accurately.
Top Page Image Contents