RIDGID MS1290LZ1 manual Specific Safety Rules

Page 5

SPECIFIC SAFETY RULES

NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area.

NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason.

NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting path of the blade.

AVOID AWKWARD OPERATIONS AND HAND POSI- TIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance. NEVER operate the miter saw on the floor or in a crouched position.

NEVER stand or have any part of your body in line with the path of the saw blade.

ALWAYS release the power switch and allow the saw blade to stop rotating before raising it out of the workpiece.

DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY. This could cause the saw blade to loosen and could create a hazard. Should this ever occur, stand clear and allow the saw blade to come to a complete stop. Disconnect the saw from the power supply and securely retighten the blade bolt.

IF ANY PART OF THIS MITER SAW IS MISSING or should break, bend, or fail in any way, or should any electrical component fail to perform properly, shut off the power switch, remove the miter saw plug from the power source and have damaged, missing, or failed parts replaced before resuming operation.

IF THE POWER SUPPLY CORD IS DAMAGED, it must be replaced only by the manufacturer or by an authorized service center to avoid risk.

ALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your saw) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.

MAKE SURE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using your saw.

ALWAYS TURN OFF THE SAW before disconnecting it to avoid accidental starting when reconnecting to power supply. NEVER leave the saw unattended while connected to a power source.

THIS TOOL has the following markings:

a)Wear eye protection.

b)Keep hands out of path of saw blade

c)Do not operate saw without guards in place.

d)Do not perform any operation freehand.

e)Never reach around saw blade.

f)Turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

g)Disconnect power (or unplug tool as applicable) before changing blade or servicing.

h)No load speed.

ALWAYS MAKE SURE THE SAW BLADE HAS CLEAR- ANCE OF ALL OBSTRUCTIONS BEFORE TURNING THE SAW ON.

MAKE SLIDING CUTS by pushing the saw blade down on top of the workpiece then sliding it back toward the rear of the saw. DO NOT pull the saw toward you while making a cut.

ALWAYS carry the tool only by the carrying handles.

AVOID direct eye exposure when using the laser guide.

SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents OPERATOR’S Manual Introduction Table of Contents Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications Features12 IN. Blade Know Your Compound Miter SAWAMP Motor Bevel Lock LeverMiter Lock Lever Switch TriggerMiter Scale Miter ThumbwheelRatchet Tools NeededCombination Square Phillips Screwdriver Framing SquareFlat Head Socket CAP Screw Loose PartsDust BAG Mounting Holes AssemblyUnpacking Locking / Unlocking the SAW ARM Using the Depth GuideSAW ARM Depth GuideInstalling the Work Clamp Installing the Dust BAGDust BAG Frame Guide Exhaust Port Work ClampBlade Installing / Replacing the BladeOuter Blade Washer Loosen Washer HEX Boltinner Blade Washer withAligning the Laser Guide Line Mounting the Exactline Laser GuideLaser Broken RED LineCentering the SAW Blade Between the Slide Bars Removing / Replacing the Zero CLEAR- Ance Throat PlateSquaring the SAW Blade to the Fence Adjusting the Miter Lock LeverSee Figures 18 See Figures 20View of Blade Square with Fence Miter Scale Indicator FigAdjusting the Bevel Pivot Adjusting the Bevel Lock LeverTravel Pivot Adjustment See Figures 25Squaring the Blade to the Miter Table IndicatorSee Figures 28 Sliding Miter FenceCutting with Your Sliding Compound Miter SAW OperationApplications Slide CUT Slide SAW ARM Forward then Push Down Back To Slide CUTSee Figures 32 Work Clamp Cross CUT Miter CUT To Miter CUT / Cross CUTSee Figures 34 To Bevel CUT Scale Indicator BevelSee Figures 36 Bevel CUT Clamp Lock PINCompound Miter CUT To Compound Miter CUTClamping Wide Workpieces Supporting Long WorkpiecesSee Figures 40 Long WorkpieceRough Cutting a Dado Using AN Auxiliary FenceSee Figures 43 Depth Guide CUT These Grooves With SAWPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceCrown Molding JIG Using a Crown Molding Support JIGMaking a Crown Molding Support JIG General Maintenance MaintenanceCutting Warped Material LubricationAdjusting Socket Head Screw Brush ReplacementMotor Belt Tension Brush CAP Belt CoverDo not attempt to activate the laser Changing the BatteriesLaser Guide Screws Aperture Cover KEY KEYMiter Saw Utility Vehicle AccessoriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1290LZ1 Serial No Customer Service Information

MS1290LZ1 specifications

The RIDGID MS1290LZ1 is a powerful miter saw designed for both professional tradespeople and avid DIYers, providing exceptional versatility, precision, and ease of use. With its robust features and innovative technologies, this miter saw stands out in the crowded market of power tools.

One of the standout features of the MS1290LZ1 is its powerful 15-amp motor, which generates an impressive 4,000 RPM. This high-speed operation allows for quick and clean cuts through various materials, including hardwood, softwood, and composites. Capable of making both bevel and miter cuts, the saw offers a cutting capacity of up to 12 inches, making it suitable for a range of applications, from framing to crown molding.

The MS1290LZ1 is equipped with a dual bevel system, allowing users to make beveled cuts to the left and right with ease. This means that operators can achieve precise angles without the need to flip or reposition their workpieces, significantly enhancing efficiency. The saw features a generous cutting capacity of 0 to 50 degrees for miter cuts on both sides, enabling a wide variety of projects with intricate angles.

Another notable characteristic of this miter saw is its advanced laser guide system. This technology projects an accurate line of cut directly onto the material, ensuring maximum precision. The adjustable laser can be aligned with the blade for improved accuracy, reducing the likelihood of errors. Additionally, the MS1290LZ1 includes a built-in work light that illuminates the cutting area, providing visibility in low-light environments.

The saw's ergonomic design enhances user comfort during operation. Equipped with a sturdy and lightweight chassis, the MS1290LZ1 is easy to transport, making it an excellent choice for on-site jobs. The handle features a comfortable grip, allowing for extended use without causing fatigue. Moreover, the saw includes a dust collection port that helps maintain a clean workspace by minimizing sawdust and debris.

In conclusion, the RIDGID MS1290LZ1 miter saw combines power, precision, and user-friendly features, making it an ideal tool for both novice and experienced users. With its powerful motor, dual bevel capabilities, advanced laser guide, and ergonomic design, this miter saw offers the versatility and performance needed to tackle any cutting task with confidence. Whether you're framing a house, crafting custom furniture, or working on detailed trim, the MS1290LZ1 is equipped to handle the job efficiently and accurately.
Top Page Image Contents