RIDGID MS1290LZ1 manual Installing the Dust BAG, Installing the Work Clamp, Quick Release Lever

Page 17

ASSEMBLY

INSTALLING THE DUST BAG

See Figure 11.

Squeeze the metal clips on the dust bag, then slide the metal ring over the end of the dust guide. Position the metal ring so it is between the two molded rings on the dust guide. Release the dust bag clips.

Snap the frame onto the slide bar by squeezing the dust bag frame, then pushing it down over the slide bar.

Insert the dust guide inside the exhaust port in the upper blade guard.

Slip the dust bag over the frame with the zipper facing down.

NOTE: For efficient operation, empty the dust bag before it is half full. This will permit better air flow through the bag.

INSTALLING THE WORK CLAMP

See Figure 12.

WARNING:

In some operations, the work clamp assembly may interfere with the operation of the blade guard assembly. Always make sure there is no interfer- ence with the blade guard prior to beginning any cutting operation to reduce the risk of serious personal injury.

The work clamp provides greater control by clamping the workpiece to the miter table. It also helps to prevent the workpiece from creeping toward the saw blade. This is very helpful when cutting compound miters. Depending on the cutting operation and the size of the workpiece, it may be necessary to use a C-clamp instead of the work clamp to secure the workpiece prior to making the cut. The work clamp can be installed and used on either side of the blade.

To install the work clamp:

Place the work clamp shaft in one of the holes located behind the sliding miter fence.

NOTE: Align the pin on the work clamp shaft with the slot in the hole.

Rotate the knob on the work clamp to move it up or down as needed.

NOTE: The work clamp has a quick release lever that makes positioning of the work clamp effortless. Push the button on the side of the work clamp to quickly release the workpiece.

DUST BAG FRAME

DUST BAG FRAME

DUST

GUIDE EXHAUST

PORT

DUST BAG

 

Fig. 11

 

WORK CLAMP

WORK CLAMP

SHAFT

QUICK

RELEASE

LEVER

Fig. 12

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents OPERATOR’S Manual Introduction Table of Contents Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications Features12 IN. Blade Know Your Compound Miter SAWAMP Motor Bevel Lock LeverMiter Lock Lever Switch TriggerMiter Scale Miter ThumbwheelRatchet Tools NeededCombination Square Phillips Screwdriver Framing SquareFlat Head Socket CAP Screw Loose PartsDust BAG Mounting Holes AssemblyUnpacking Locking / Unlocking the SAW ARM Using the Depth GuideSAW ARM Depth GuideInstalling the Work Clamp Installing the Dust BAGDust BAG Frame Guide Exhaust Port Work ClampBlade Installing / Replacing the BladeOuter Blade Washer Loosen Washer HEX Boltinner Blade Washer withAligning the Laser Guide Line Mounting the Exactline Laser GuideLaser Broken RED LineCentering the SAW Blade Between the Slide Bars Removing / Replacing the Zero CLEAR- Ance Throat PlateSquaring the SAW Blade to the Fence Adjusting the Miter Lock LeverSee Figures 18 See Figures 20View of Blade Square with Fence Miter Scale Indicator FigAdjusting the Bevel Pivot Adjusting the Bevel Lock LeverTravel Pivot Adjustment See Figures 25Squaring the Blade to the Miter Table IndicatorSee Figures 28 Sliding Miter FenceCutting with Your Sliding Compound Miter SAW OperationApplications Slide CUT Slide SAW ARM Forward then Push Down Back To Slide CUTSee Figures 32 Work Clamp Cross CUT Miter CUT To Miter CUT / Cross CUTSee Figures 34 To Bevel CUT Scale Indicator BevelSee Figures 36 Bevel CUT Clamp Lock PINCompound Miter CUT To Compound Miter CUTClamping Wide Workpieces Supporting Long WorkpiecesSee Figures 40 Long WorkpieceRough Cutting a Dado Using AN Auxiliary FenceSee Figures 43 Depth Guide CUT These Grooves With SAWPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceCrown Molding JIG Using a Crown Molding Support JIGMaking a Crown Molding Support JIG General Maintenance MaintenanceCutting Warped Material LubricationAdjusting Socket Head Screw Brush ReplacementMotor Belt Tension Brush CAP Belt CoverDo not attempt to activate the laser Changing the BatteriesLaser Guide Screws Aperture Cover KEY KEYMiter Saw Utility Vehicle AccessoriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1290LZ1 Serial No Customer Service Information

MS1290LZ1 specifications

The RIDGID MS1290LZ1 is a powerful miter saw designed for both professional tradespeople and avid DIYers, providing exceptional versatility, precision, and ease of use. With its robust features and innovative technologies, this miter saw stands out in the crowded market of power tools.

One of the standout features of the MS1290LZ1 is its powerful 15-amp motor, which generates an impressive 4,000 RPM. This high-speed operation allows for quick and clean cuts through various materials, including hardwood, softwood, and composites. Capable of making both bevel and miter cuts, the saw offers a cutting capacity of up to 12 inches, making it suitable for a range of applications, from framing to crown molding.

The MS1290LZ1 is equipped with a dual bevel system, allowing users to make beveled cuts to the left and right with ease. This means that operators can achieve precise angles without the need to flip or reposition their workpieces, significantly enhancing efficiency. The saw features a generous cutting capacity of 0 to 50 degrees for miter cuts on both sides, enabling a wide variety of projects with intricate angles.

Another notable characteristic of this miter saw is its advanced laser guide system. This technology projects an accurate line of cut directly onto the material, ensuring maximum precision. The adjustable laser can be aligned with the blade for improved accuracy, reducing the likelihood of errors. Additionally, the MS1290LZ1 includes a built-in work light that illuminates the cutting area, providing visibility in low-light environments.

The saw's ergonomic design enhances user comfort during operation. Equipped with a sturdy and lightweight chassis, the MS1290LZ1 is easy to transport, making it an excellent choice for on-site jobs. The handle features a comfortable grip, allowing for extended use without causing fatigue. Moreover, the saw includes a dust collection port that helps maintain a clean workspace by minimizing sawdust and debris.

In conclusion, the RIDGID MS1290LZ1 miter saw combines power, precision, and user-friendly features, making it an ideal tool for both novice and experienced users. With its powerful motor, dual bevel capabilities, advanced laser guide, and ergonomic design, this miter saw offers the versatility and performance needed to tackle any cutting task with confidence. Whether you're framing a house, crafting custom furniture, or working on detailed trim, the MS1290LZ1 is equipped to handle the job efficiently and accurately.
Top Page Image Contents