RIDGID R3202 manual Operation, Applications, Kickback, See Figures 4, Workpiece

Page 12

OPERATION

WARNING:

Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

56

56

56

Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

APPLICATIONS

You may use this product for the purposes listed below:

Cutting all types of wood products (lumber, plywood, paneling, composition board, and hard board)

Cross cutting/Rip cutting

Bevel cutting

Pocket cutting

NOTE: The use of abrasive cut-off wheels is not recom- mended for this saw.

KICKBACK

See Figures 4 - 7.

Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood.

KICKBACK - BLADE SET TOO DEEP

INCORRECT SUPPORT

Fig. 4

Fig. 5

DANGER:

Release switch immediately if blade binds or saw stalls. Kickback could cause you to lose control of the saw. Loss of control can lead to serious personal injury.

To guard against kickback, avoid dangerous practices such as the following:

Setting blade depth incorrectly.

Sawing into knots or nails in workpiece.

Twisting the blade while making a cut.

Making a cut with a dull, gummed up, or improperly set blade.

Supporting the workpiece incorrectly.

Forcing a cut.

Cutting warped or wet lumber.

Operating the tool incorrectly or misusing the tool.

To lessen the chance of kickback, follow these safety practices:

Keep the blade at the correct depth setting. Less than a full tooth of the blade teeth should be visible below the workpiece.

Inspect the workpiece for knots or nails before cutting. Never saw into a knot or nail.

LOWER BLADE GUARD IS IN UP

POSITION WHEN MAKING A CUT

56

CORRECT BLADE DEPTH SETTING = Less than a full tooth of the blade teeth should be visible below

the workpiece.

Fig. 6

 

 

Make straight cuts. Always use a straight edge guide when rip cutting. This helps prevent twisting the blade.

Use clean, sharp, and properly set blades. Never make cuts with dull blades.

Support the workpiece properly before beginning a cut.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OPERATOR’S Manual Double InsulatedTable of Contents IntroductionGeneral Power Tool Safety Warnings and Instructions Work Area SafetyElectrical Safety Personal SafetyCircular SAW Safety Warnings and Instructions Causes and Operator Prevention of KickbackAdditional Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionFeatures Product SpecificationsAssembly Attaching Blade Removing BladeSee Figures 2 SeeOperation ApplicationsKickback See Figures 4SAW Blades Blade Guard SystemAdjusting Blade Depth STARTING/STOPPING the SAWIndexable Levers Operating the SAW See Figures 12RIP CUTting Bevel CuttingSee Figures 15 See Figures 17Pocket Cutting Bevel CuttingAdjustments Positive 0 Bevel StopSee Figures 21 Maintenance AccessoriesGeneral Maintenance Power Supply cord ReplacementPage Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No R3202 Serial No

R3202 specifications

The RIDGID R3202 is a sophisticated tool designed for professionals and DIY enthusiasts alike, primarily known for its versatility and robust performance in various tasks. This oscillating multi-tool excels in a wide range of applications, making it a valuable addition to any toolkit.

One of the key features of the R3202 is its powerful 3-amp motor, which delivers a variable speed range of 11,000 to 20,000 oscillations per minute. This allows users to adjust the speed according to the material being worked on, whether it's wood, metal, drywall, or other surfaces. The quick-release blade change system enhances productivity by enabling fast and effortless swaps between different attachments, ensuring you can switch tasks without delay.

The tool incorporates a 3.0-degree oscillation angle, providing efficient cutting and sanding operations while minimizing strain on the user. Additionally, the R3202 comes equipped with a rubber overmold grip for comfort and control, allowing users to work for longer periods without fatigue. This thoughtful design feature enhances grip, ensuring that the tool remains securely in hand during operation.

Another highlight of the RIDGID R3202 is its compatibility with various accessories. It utilizes the RIDGID Universal Fit System, which means that it can accommodate a wide selection of blades and sanding pads from multiple brands, giving users the flexibility to choose the best accessories for their specific projects. This ensures that whether you are performing precise cuts or detailed sanding, the tool is versatile enough to handle the job.

The multiple oscillating tool also features a removable dust extraction port, allowing users to maintain a cleaner workspace while minimizing dust inhalation during use. This is particularly essential for maintaining a safe and efficient working environment.

In addition to these features, the RIDGID R3202 is built with durability in mind. The tough construction materials ensure that it can withstand the rigors of job site use, providing reliable performance over time. This tool also comes with the RIDGID Lifetime Service Agreement, offering peace of mind through free parts and service for life, making it an excellent investment for both professionals and hobbyists.

Overall, the RIDGID R3202 is a powerful, flexible, and reliable oscillating multi-tool that stands out in the crowded market of power tools. Its combination of features, durability, and user comfort makes it an essential tool for a variety of cutting and sanding applications.
Top Page Image Contents