Emerson KF160OI01 Grommet, Hairpin Clip Setscrew Downrod Motor Coupling Clevis PIN, Pin

Page 7

BP7283, High Country, KF160 7/31/06 10:54 AM Page 7

!WARNING

It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tight- ened. Failure to verify that the pin and setscrews are properly installed (as shown in Figure 5) could result in the fan falling.

tight against the pin and securely tight- en the setscrew in the hanger ball. A loose setscrew could create fan wobble.

 

DOWNROD

GROMMET

DECORATIVE

HAIRPIN

CLIP

SETSCREW (2)

Figure 6

DOWNROD

MOTOR

COUPLING

CLEVIS PIN

COVER

DECORATIVE

SCROLL

ASSEMBLY

10. Tighten the setscrews (Figure 6) secure- ly while pulling up on the downrod.

NOTE: The setscrews must be properly installed as described above, or fan wobble could result.

NOTE: If you installed the 3-1/2” down- rod, the decorative scroll assembly and decorative cover will not be installed. Disregard the next step.

11. Make sure the grommets are properly installed in the decorative scroll assembly and in the decorative cover. Slide the decorative scroll over the downrod until it rests on the motor housing. (Figure 7). Then slide the decorative cover over the downrod until it rests on the top of the decora- tive scroll.

12. Place the ceiling cover over the down- rod. Then reinstall the hanger ball (Figure 8) on the downrod as follows. Route the four 80” motor leads through the hanger ball and slide the hanger ball over the downrod. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up

40-WATT CANDELABRA BASE ROUND BULB (3)

Figure 7

!WARNING

It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling.

PIN

HANGER BALL

CEILING COVER

SETSCREW

DOWNROD

Figure 8

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents High Country Additional Safety Instructions for Installation Safety InstructionsMaterials General General Preset Memory FeatureInstallation of Battery Setting Operating Frequency of Transmitter ReceiverRubber Washer Upper Glass Motor Housing Assembly How to Assemble Your Ceiling FanElectrical Requirements Screw Adapter Plate Cutout for Flange Screw Access BladeFiber Washer Truss HeadPIN Decorative Scroll AssemblyGrommet Hairpin Clip Setscrew Downrod Motor Coupling Clevis PINAT Least How to Hang Your Ceiling FanCeiling Outlet BOX TWO Screws Supplied With TABHow to Wire Your Ceiling Fan NUT WhiteCeiling Cover Lockwasher KnurledLower Glass Light Fitter Adapter White WireAdapter Light Fitte Assembly Light Fitter Socket ThreadedLowremote Control Transmitter Installation Storage BracketOperating Your Ceiling Fan Important Care Instructions MaintenanceAccessoriesTrouble Probable Cause Suggested Remedy Trouble ShootingDescription KF160OI01 Repair Parts ListingLimited Warranty

KF160OI01 specifications

The Emerson KF160OI01 is a cutting-edge cooling solution designed for commercial and industrial applications, boasting a range of features that cater to efficiency, reliability, and ease of use. One of the standout aspects of this unit is its advanced refrigerant technology, which utilizes eco-friendly refrigerants to reduce environmental impact while maximizing cooling performance.

At its core, the KF160OI01 is engineered with a high-efficiency compressor that operates quietly and effectively, ensuring optimal performance while keeping energy costs low. This compressor is paired with a high-capacity condenser coil that enhances heat exchange capabilities, allowing the unit to cool large spaces quickly and effectively. This makes the KF160OI01 ideal for environments that require rapid temperature control, such as restaurants, warehouses, and manufacturing facilities.

Additionally, the Emerson KF160OI01 incorporates intelligent control systems that allow for precise temperature regulation. These smart controls enable users to set specific temperature thresholds and monitor energy consumption, enhancing overall operational efficiency. The inclusion of a digital display and user-friendly interface further simplifies the monitoring and adjustment of settings, making it easy for operators to maintain optimal conditions.

Durability is another significant characteristic of the KF160OI01. The unit is built with robust materials designed to withstand the rigors of continuous operation in demanding environments. This longevity is complemented by a built-in self-diagnostic feature that alerts users to any potential issues before they escalate, minimizing downtime and maintenance costs.

Furthermore, the KF160OI01 is designed with flexibility in mind. Its modular construction allows for easy integration into existing systems or replacement of older units. This adaptability ensures that it can meet a variety of installation requirements while providing consistent performance.

In summary, the Emerson KF160OI01 represents a pinnacle of innovation in commercial cooling technology. With its focus on energy efficiency, advanced controls, and durability, it stands out as a reliable solution for businesses looking to enhance their environmental comfort while minimizing costs and energy consumption. As industries increasingly prioritize sustainable practices, the KF160OI01 is poised to meet future demands, making it a wise investment for any commercial operation.
Top Page Image Contents