How to Wire Your Ceiling Fan

BP7283, High Country, KF160 7/31/06 10:54 AM Page 9

2. Refer to Figure 12 and 13 and connect the receiver wires to the supply wires and the fan motor wires as follows:

If you feel that you do not have enough electrical wiring knowledge or experi- ence, have your fan installed by a licensed electrician.

!WARNING

Turning off wall switch is not suffi- cient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precau- tion against possible electrical shock.

CAUTION: To reduce the risk of electri- cal shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver.

1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12.

NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire.

a.Securely connect the green grounding wires from the hanger ball and the hanger bracket to the supply grounding conductor (this may be a bare wire or a wire with green insulation).

b.Securely connect the supply white (neutral) wire to the receiver white (AC IN N) wire.

c.Securely connect the supply black wire (hot) wire to the receiver black (AC IN

L)wire.

d.Securely connect the fan motor white wire to the receiver white (TO MOTOR

N)wire.

e.Securely connect the fan motor black wire to the receiver black (TO MOTOR

L)wire.

f.Securely connect the fan motor blue wire to the receiver blue (FOR BOTTOM LIGHT) wire.

g.Securely connect the fan motor orange wire to the receiver orange (FOR UPPER LIGHT) wire.

!WARNING

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire con- nectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.

	SUPPLY WHITE WIRE
	(NEUTRAL)
SUPPLY BLACK	A
	C I
WIRE (HOT)	N	N
WIRE (HOT)		N
GROUND WIRE
GREEN GROUND WIRE		AC IN L
GREEN GROUND WIRE
FROM HANGER BALL
ANTENNA
GREEN GROUND WIRE		FAN BLACK
FROM HANGER BRACKET		WIRE
1-1/4" THREADED	FAN BLUE WIRE
STUD (2)	FAN WHITE WIRE

Figure 12

RECEIVER WHITE

WIRE

RECEIVER BLACK WIRE

RECEIVER BLACK

WIRE

RECEIVER

BLUE WIRE

		LIGHT		MOTOR	L		LIGHT
MOTOR	N	BOTTOM		MOTOR		UPPER
			TO		FOR	UPPER	RECEIVER
			TO				RECEIVER
TO		FOR					ORANGE WIRE

FAN ORANGE

WIRE

RECEIVER WHITE

WIRE

KF160OI01 specifications

The Emerson KF160OI01 is a cutting-edge cooling solution designed for commercial and industrial applications, boasting a range of features that cater to efficiency, reliability, and ease of use. One of the standout aspects of this unit is its advanced refrigerant technology, which utilizes eco-friendly refrigerants to reduce environmental impact while maximizing cooling performance.

At its core, the KF160OI01 is engineered with a high-efficiency compressor that operates quietly and effectively, ensuring optimal performance while keeping energy costs low. This compressor is paired with a high-capacity condenser coil that enhances heat exchange capabilities, allowing the unit to cool large spaces quickly and effectively. This makes the KF160OI01 ideal for environments that require rapid temperature control, such as restaurants, warehouses, and manufacturing facilities.

Additionally, the Emerson KF160OI01 incorporates intelligent control systems that allow for precise temperature regulation. These smart controls enable users to set specific temperature thresholds and monitor energy consumption, enhancing overall operational efficiency. The inclusion of a digital display and user-friendly interface further simplifies the monitoring and adjustment of settings, making it easy for operators to maintain optimal conditions.

Durability is another significant characteristic of the KF160OI01. The unit is built with robust materials designed to withstand the rigors of continuous operation in demanding environments. This longevity is complemented by a built-in self-diagnostic feature that alerts users to any potential issues before they escalate, minimizing downtime and maintenance costs.

Furthermore, the KF160OI01 is designed with flexibility in mind. Its modular construction allows for easy integration into existing systems or replacement of older units. This adaptability ensures that it can meet a variety of installation requirements while providing consistent performance.

In summary, the Emerson KF160OI01 represents a pinnacle of innovation in commercial cooling technology. With its focus on energy efficiency, advanced controls, and durability, it stands out as a reliable solution for businesses looking to enhance their environmental comfort while minimizing costs and energy consumption. As industries increasingly prioritize sustainable practices, the KF160OI01 is poised to meet future demands, making it a wise investment for any commercial operation.