Sears owner manual General Information, Glossary, Specification Chart, Model No 919.726330

Page 5

GENERAL INFORMATION

You have purchased an air compressor unit consisting of a one cylinder, single-stage air compressor pump and air tank.

This air compressor requires no oil. Now you can enjoy all the benefits of having an air compressor without ever having to purchase, add or change oil.

Your air compressor can be used for operating paint spray guns, air tools, blow guns, nailers/staplers, air brushes,

and inflator kits. An air pressure regulator is required for most of the applications.

An inline air filter which removes moisture and dirt from compressed air should be used where applicable.

An inline regulator can be used if a more precise adjust- ment of air pressure is needed downstream.

GLOSSARY

CFM: Cubic Feet per Minute.

SCFM: Standard Cubic Feet per Minute; a unit of mea- sure of air delivery.

PSI: Pounds per Square Inch; a unit of measure of pressure.

ASME: American Society of Mechanical Engineers; made, tested, inspected and registered to meet the standards of the ASME.

Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level and the pressure switch lever is in "Auto", the motor will restart automati- cally. The low pressure at which the motor automatically restarts is called “cut-in pressure.”

Cut-Out Pressure: When you turn on your air compres- sor and it begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called “cut-out pressure.”

CSA: Electrical products sold in Canada are required to be certified to the applicable CSA standard (s). Canadian Standards Association (CSA) is a standards writing and safety testing organization. Products that are CSA certified have been evaluated and tested and found to meet or exceed the applicable CSA standard (s) for safety and electrical performance.

SPECIFICATION CHART

Model No.

919.726330

Number of Cylinders

2

Bore

2 3/8"

Stroke

1.2"

Voltage - Single Phase

240

Minimum Branch Circuit Requirement

15 amps

Fuse Type

Time Delay

Amperage at Maximum Pressure

15.0

Air Tank/Capacity

ASME/33 gal. (U.S.)

Approximate Cut-in Pressure

100

Approximate Cut-out Pressure

125

SCFM @ 40 psi

15.0

SCFM @ 90 psi

11.5

5

Image 5
Contents MGP-726330 10/1/96 Model No 919.726330Table of Contents What to Look for What could Happen HOW to Prevent IT Safety GuidelinesWhat could Happen HOW to Prevent IT General Information Specification ChartGlossary Model No 919.726330Description of Operation Tools Needed for AssemblyLocation of the Air Compressor BREAK-IN ProceduresVoltage and Circuit Protection Operating ProceduresCheck Valve Cleaning Replacement MaintenanceProblem Cause Correction Troubleshooting GuideTroubleshooting Guide Service Notes Service Notes Service and Repair Parts De modèle Tension et protection du circuit Table DES MatièresAvertissement Consignes DE SécuritéAir comprimé Glossaire Information GénéraleTableau DES Spécifications De modèle Nombre de cylindres AlésageOutils Nécessaires À L’ASSEMBLAGE Description DU FonctionnementEmplacement du compresseur Installation ET RodageAssemblage Lubrification et huileDirectives de rodage Mise EN MarcheTension et protection du circuit Entretien Clapet de retenue Nettoyage et remplacementSoupape de sûreté Inspection MoteurGuide DE Dépannage Problème Cause SolutionGuide DE Dépannage suite Page Page DE Modèle Entretien Pour Commander DES Pièces DE Rechange