Emerson CF945HTW, CF945WB, CF945PW, CF945AB owner manual TOP Align with Outer Edge Housing Socket

Page 6

PIN

HANGER

BALL SETSCREW

DOWNROD

CEILING COVER

CEILING

AT LEAST

7'

Figure 5

Figure 7

FLOOR

5.Reinstall the hanger ball (Figure 5) on the downrod as follows. Route the two 80” motor leads through the hanger ball. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin. Securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble.

!WARNING

It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are proper- ly installed could result in the fan falling.

6.Screw in four 40-watt (maximum) candelabra base lamps in the housing sockets (Figure 6). Grasp the sockets and pivot them until the lamp bulbs are even with the outer edge of the housing as shown. This will provide the optimum lighting effect.

!WARNING

The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician in in doubt.

8.Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box. (Figure 8.)

!WARNING

Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.

TOP ALIGN WITH

OUTER EDGE OF

THE HOUSING

SOCKET

 

Figure 6

CANDELABRA

BASE LAMP

7.The fan comes with black and white leads that are 80” long. Before installing fan, measure up approxi- mately 6 to 9-inches above top of hanger ball/down- rod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

!WARNING

The fan must be hung with at least 7' of clearance from floor to blades (Figure 7).

6

 

OUTLET

 

BOX

TWO SCREWS

 

SUPPLIED WITH

HANGER

OUTLET BOX

 

BRACKET

Figure 8

TAB

 

9.Carefully lift the fan and seat the hanger ball/down- rod assembly on the hanger bracket that was just attached to the outlet box (Figure 9). Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 8).

!WARNING

Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.

!WARNING

To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Read and Save These Instructions Safety Instructions Unpacking Instructions Electrical Requirements Preset Memory FeatureInstallation of Battery GeneralSetting Operating Frequency of Transmitter Receiver How to Put Your Ceiling Fan TogetherTOP Align with Outer Edge Housing Socket Supply Wires Install Through Slots Installation of the Decorative Support Rods Assembly ROD Support Assembly Setscrew DownrodAccessories Installation Storage BracketMaintenance OperationTrouble Shooting Trouble Probable Cause Suggested RemedyRepair Parts Air Comfort Products

CF945AB, CF945HTW, CF945PW, CF945WB specifications

The Emerson CF945HTW, CF945PW, CF945AB, and CF945WB are impressive ceiling fans that blend elegance with advanced technology, making them ideal for various settings, from modern homes to commercial spaces. These models stand out not only for their aesthetic appeal but also for their energy efficiency and reliable performance.

One of the main features of the CF945 series is the stylish design, which includes a range of finishes such as white, brushed nickel, antique brass, and walnut. This variety enables homeowners and decorators to seamlessly integrate the fans into their desired décor theme. Each model sports a sleek, contemporary profile with a five-blade configuration that enhances both airflow and visual balance.

The 52-inch blade span is specifically engineered for optimal air circulation in medium to large rooms. The CF945 fans operate quietly, thanks to a powerful and efficient motor that ensures a pleasant atmosphere without disruptive noise. With the versatility of three-speed settings, users can easily adjust airflow to suit their comfort level.

Another significant characteristic of these fans is their incorporation of the Energy Star rating, underscoring their energy efficiency and commitment to sustainability. The Emerson CF945 series is designed to minimize energy consumption while still maximizing performance, making it an eco-friendly cooling solution.

In terms of technologies, these fans are equipped with a dual mount system, allowing for both standard and angled mounting. This feature enhances installation flexibility, making it easier for homeowners to incorporate the fans in various ceiling heights. The fans also come with integrated light fixtures, available in multiple wattage options, providing ambient lighting alongside the cooling breeze.

Remote control functionality is another key feature, enabling homeowners to operate the fans effortlessly from across the room. This convenience allows for adjustments without the need to get up, enhancing the overall user experience. The easy-to-follow assembly instructions facilitate a quick installation process, making the Emerson CF945 series an excellent choice for those seeking a combination of style, effectiveness, and technology. In summary, the Emerson CF945HTW, CF945PW, CF945AB, and CF945WB ceiling fans deliver a perfect balance of design and functionality, suitable for enhancing any indoor space.
Top Page Image Contents