Emerson CF943 owner manual WAY WIRlNG Diagram NEW Construction, How to Assemble Your, Ceiling Fan

Page 7

BP7335 Palazzo 1/9/07 9:05 AM Page 7

4. Install a wall control in the wall box containing the “hot” wire first. Connect one black wire of the wall control to the “hot” wire. Securely connect wires with wire connectors supplied.

5. Connect the other black wire of the wall control to both remaining traveler wire(s) in the wall box and secure with wire connector supplied.

NOTE: Retrofit 3-way installations are likely to include two traveler wires between the two wall boxes. In new construction, only one traveler wire is required.

STANDARD WIRING FOR EXISTING 3-WAY CONTROLS

EXISTING

WALL CONTROL

HOT BLK

 

 

BLACK

TRAVELER WIRES

LOAD

 

3-WAY WIRING DIAGRAM: RETROFIT

3-WAY WIRlNG DIAGRAM: NEW CONSTRUCTION

EXISTING

WALL CONTROL

HOT BLK

HOT

 

FAN/LIGHT

 

 

 

BLACK

 

 

WALL

 

 

 

 

 

EMERSON

CONTROL

EMERSON

 

TRAVELER WIRES

 

 

 

 

 

 

LOAD

BLACK

 

 

 

 

 

 

BLK

 

BLK

Figure 5

 

 

 

 

 

 

 

 

TRAVELER

 

LOAD

 

 

 

 

 

BLACK

 

 

NEUTRAL

 

WIRE

 

GROUND

 

 

 

 

 

REMOTE CONTROL

 

 

How to Assemble Your

RECEIVER LOCATED

 

 

Ceiling Fan

 

WITHIN THE CEILING

 

 

 

COVER

 

 

 

 

 

 

Figure 4

! WARNING

6. Place wall control into wall box. Screw in place and install decorator style faceplate (included).

7. Next, install the other wall control into the wall box containing the “load” wire. Connect one black wire of the wall control to the traveler wire(s) already connected to the black wire (in the other wall box). Secure with wire connectors supplied.

8. Connect the other black wire of the wall control to the “load” (black) wire and secure with wire connector supplied.

9. Place the second wall control into the wall box. Screw in place and install decorator style faceplate (included).

Leave switch in “OFF” mode until fan installation is completed.

10. Refer to “How to Assemble Your Ceiling Fan” section to complete the assembly of your ceiling fan.

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

1.Mount blade flanges to fan blades using three #10-32 x 5/16” pan head blade screws and three #10 flat blade washers (supplied in loose parts bag) (Figure 6).

!WARNING

To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.

7

Image 7
Contents CF943AGW00 CF943BZH00 Additional Safety Instructions for Installation Safety InstructionsMaterials Tools Needed for AssemblyUnpacking Instructions FAN Motor Assembly Coupling Cover Ceiling Cover FAN Blades Setting Operating Frequency of Wall Control Receiver Figure Electrical Requirements Ceiling Fan ProceduresGeneral WAY Installation How to Assemble Your WAY WIRlNG Diagram NEW ConstructionCeiling Fan Turn the fan motor assembly Upside down onto the styrofoam Wobble could result Tighten as described above, or fanHow to Hang Your Ceiling Fan How to Wire Your Ceiling Fan Supply Ground Wire Green or Bare Receiver White Supply How to Install Your Light Kit Light Operating Your Ceiling FanInstruction to the User For your Ceiling Fan MaintenanceAccessoriesTrouble Probable Cause Suggested Remedy Trouble ShootingHOW to Order Repair Parts Repair PartsDescription Repair Parts ListingPart Numbers KeyLimited Warranty