Husqvarna MC 18 13H, MC 18 9H Check Before Starting Starting The Power Source, Fitting The Blade

Page 13

4

Check Before Starting

6

Starting The Power Source

Take into account the working conditions from the health and safety point of view.

FUEL: Check the engine maintenance manual.

*Gas Models: Unleaded gasoline is recommended.

•Check that the engine oil level is correct. Because the engine often operates at an angle, check the oil level (with engine horizontal) frequently to ensure that the oil level never falls below the lower mark on the dipstick. 10W30 oil is recommended.

5

Fitting The Blade

(See Fig. 1 and 2)

Always set the Engine Switch (1D) to the "OFF" position before mounting the Blade (2E).

•Set the Engine Switch (1D) to the "OFF" position.

•Raise the machine to a high position [by cranking the Raise/Lower Hand Wheel].

•Raise the front half of the Blade Guard (2H).

•Unscrew the Blade Shaft Nut (2A). Remove Outer Flange (2B).

•Fit Diamond Blade (2E) on the Blade Shaft Arbor.

•Install Outer Flange (2B) into the Blade Shaft (2I) making sure that the Locking Pin (2D) passes through the Diamond Blade (2E) and into the Inner Flange (2F).

Note the direction of rotation of the blade. The direction of rotation is shown by an arrow on the Diamond Blade (2E). Make sure that the contact surfaces on the Diamond Blade (2E), Inner & Outer Flanges (2B & 2F) and Blade Arbor are clean.

•Rotate Outer Flange (2B) and the Blade (2E) in the opposite direction of blade rotation to remove back- lash.

•Install and tighten Blade Flange Nut using the Blade Shaft Wrench [50 lb.-ft. (68 N-m)] while firmly holding the Diamond Blade (2E).

•Lower front half of Blade Guard (2H).

The Blade Shaft Nut (2A) on the Right Hand side has Left Hand threads.

Always pay extreme care and attention to the preparation of the machine before starting.

Remove all wrenches and tools from the floor and the machine.

Always keep blade guard and transmission guard in place.

On Gasoline Engine Models:

1.Refer to the engine operating manual for proper engine operation.

2.Fill the engine fuel tank and check the engine oil level. Refer to the engine manual for detailed information.

3.Start the engine. Refer to the engine manual for detailed information.

4.Let the engine warm up at half throttle. All sawing is done at full throttle. The governor is factory set for the correct engine speed. Do not change the Governor setting – it is factory set for the correct speed.

WARNING: To STOP ENGINE, PUSH the Engine Stop Switch DOWN, located on the handle support of the saw. [Wait for all engine movement to stop.]

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Husqvarna Construction Products Contents Symbol Definitions Definición De Simbolos Page Atencion Page SAW Dimensions Inches mm MC 18 SpecificationsDO’s and do NOT’s Do not 2C. not Used PRE Operation Checklist Features AssemblyGeneral Instructions Fitting The Blade Check Before Starting Starting The Power SourceTo Maneuver the Saw Engine OIL MaintenanceGovernor Speed Service PartsRepairs Nota Diagram 1 Frame & Axle Bill of Material Index Description QTY Diagram 2 Depth Control Screw Feed Diagram 2 Depth Control Screw Feed Diagram 3 Pointer & Belt Guard Diagram 3 Pointer & Belt Guard Diagram 4 Guards & Water Distribution Diagram 4 Guards & Water Distribution Diagram 5 Blade Guard Diagram 5 Blade Guard Diagram 6 Engine & Bladeshaft Diagram 6 Engine & Bladeshaft Diagram 7 Kit, Water Tank Page Husqvarna Construction Products N. a Corporate Office Dust Warning

MC 18 13H, MC 18 9H specifications

The Husqvarna MC 18 series, including the MC 18 9H and MC 18 13H models, represents a significant advance in the world of walk-behind and self-propelled mowers. These machines are designed to deliver exceptional performance, durability, and user comfort, making them ideal for both professional landscapers and avid garden enthusiasts.

The MC 18 9H features a powerful Honda engine, specifically engineered for reliability and efficiency. This model boasts a 9 horsepower rating, which provides ample power for various mowing conditions, from residential lawns to more challenging terrains. On the other hand, the MC 18 13H ups the ante with a 13 horsepower engine, allowing for even greater cutting efficiency and performance, making it suitable for larger areas and tougher grass types.

One of the main features of the MC 18 series is their innovative cutting technology. Both models come equipped with a robust cutting deck that ensures a clean and precise cut. The adjustable cutting heights can be set to various levels, allowing users to customize the mowing experience based on lawn type and user preference. Additionally, the side discharge and mulching capabilities provide versatility in lawn care, allowing users to choose how they want to handle grass clippings.

Technologically, Husqvarna has incorporated a range of features to enhance user experience. These models come with an ergonomic handle that reduces vibration and fatigue during extended use. The controls are conveniently placed, allowing for easy adjustments while on the move. The MC 18 series also offers a spacious grass catcher option, which minimizes the need for frequent emptying, thus improving efficiency during mowing sessions.

Durability is another hallmark of the Husqvarna MC 18 series. Built with high-quality materials, these mowers are designed to withstand the rigors of regular use. The robust structure and reliable components ensure a long lifespan, making them a wise investment for anyone looking to maintain their lawn.

In conclusion, the Husqvarna MC 18 9H and MC 18 13H are outstanding choices for those seeking efficient and durable lawn care solutions. With their powerful engines, innovative cutting technology, ergonomic design, and robust build quality, these mowers are well-equipped to tackle a variety of mowing tasks, making them a valuable addition to any homeowner or landscaper's toolkit.
Top Page Image Contents