Southbend SB1020 owner manual Machine Labels

Page 54

Model SB1020

P A R T S

For Machines Mfg. Since 8/09

Machine Labels

402

403

404

405

401

406

407

408

411

409

410

		412	413
		412
REF	PART #	DESCRIPTION
401	PSB1020401	MAIN CONTROL PANEL LABEL
402	PSBLABEL14HL	CUTTING HAZARD LABEL
403	PSBLABEL02HL	SHOCK WARNING LABEL
404	PSB1020404	MACHINE ID LABEL
405	PSBLABEL15L	ELECTRICITY LABEL
406	PSBLABEL04HL	EYE INJURY HAZARD LABEL
407	PSBLABEL01HL	READ MANUAL LABEL

414

REF	PART #	DESCRIPTION
408	PSB1020408	MACHINE NUMBER LABEL
409	PSB1020409	BIOHAZARD WARNING LABEL
410	PSB1020410	DOWNFEED CONTROLS LABEL
411	PSBPAINT01	SB GRAY TOUCH-UP PAINT
412	PSBPAINT03	SB DARK BLUE TOUCH-UP PAINT
413	PSBPAINT02	SB LIGHT BLUE TOUCH-UP PAINT
414	SB1320	SOUTH BEND NAMEPLATE 125MM

The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

-52-

Image 54

Contents Model SB1020 Scope of Manual UpdatesCustomer Service Manual FeedbackTable of Contents Features About This MachineCapabilities Identification IdentificationMachine Specifications Other Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Metal Bandsaw Safety Things Youll Need Power Supply RequirementsReparation Overview AvailabilityCircuit Requirements for For 110V Connection PrewiredCircuit Information Grounding RequirementsUnpacking InventoryExtension Cords Cleaning & Protecting Before cleaning, gather the followingBasic steps for removing rust preventative Location Lifting & Moving Leveling & MountingLeveling Bolting to Concrete Floors Machine MountsPower Connection Machine SetupTo set up the machine Inspections Adjustments Test RunTo test run your machine OperationPERATIONOverview Description of Controls & Components Blade Length Blade SelectionBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Changes To change the blade on the bandsawTo tension the blade on the bandsaw Blade TensionBlade Breakage Most common causes of avoidable blade breakage areDownfeed Pressure Blade Care & Break-InDownfeed Rate Blade CareBlade Speed Chart Chip Inspection ChartCuts to the Right Angle CutsWork Stop Cuts to the LeftVise Quick Release To adjust the blade guideBlade Guide Workpiece HoldingCutting Fluid Cutting Fluid SystemTo use the cutting fluid system Operation Tips Coolant control valveAccessories SBL Gearhead T-Shirt SBL One Good Turn T-ShirtCleaning LubricationMachine Storage GearboxTo change the gearbox oil Troubleshooting Blade Selection section beginning on Troubleshooting Blade Brush To adjust the blade brushTo adjust the angle stops Angle StopsLimit Switches To adjust the blade tension switchTo adjust the headstock travel switch To adjust the downfeed stop boltDownfeed Stop Bolt Squaring Blade To square the blade to the tableT E S ElectricalL CTRICALSafety Instructions Wiring Diagram Color KEY220V Conversion To convert the Model SB1020 toElectrical ComponentsWiringWiring Diagram G110 VACWiring Component Locations Coolant pump motor locationCabinet & Base Cabinet & Base Parts List DescriptionHead Head Parts List Drive Wheel Machine Labels R R a N T Y Southbendlathe.com